will anyone give me some food I am hungry

Answer:

1700 kg

Explanation:

Determine the total mass of the oil, m, by multiplying the density,

p= 850 kg/m3

to the volume, V = 2m3 or m=p x v.

m=pxv.

m= p x v = 850 kg / m3 x 2

m3 = 1700 kg

Answer:

ABCDEFGHIJKLMNOPQRSTUVWXYZ

Answer:

voltage

Explanation:

because it is used with a moving pointer to display readings.

Answer:

Explanation:

Brake systems are most likely to fail at the ends.  One of the most common problems is a trailer lighting splitter is left on. With time and usage, the fuse can blow interrupting the signal path from the switch to the bulb.

Answered by the ONE & ONLY #QUEEN aka #DRIPPQUEENMO

HOPE THIS HELPED!!!

Answer: C. Voltage

Explanation:

Here are some other words as well.

potential, voltage, potential drop, potential difference.

Answered by the ONE & ONLY #QUEEN aka #DRIPPQUEENMO!!!

HOPE THIS HELPED!!!

Answer:

A jackhammer.

Explanation:

A jackhammer is a pneumatic device that was invented by William Mcreavy. Later, Mcreavy sold the patent of jackhammer to Charles Brady King. The tool is a combination of chisel and hammer.  The tool is powered by compressed air to tighten or loosen an object. By using pressurized air, jackhammers help workers to drill and lossen an object.

Therefore, option A is correct.

Answer:

Impact Driver

Explanation:

Answer:

Look at the load capacity chart in the cab

Explanation:

A crane can be defined as a large, tall metallic machine or equipment that is designed with a long horizontal arm (jib) used for the lifting and movement of very heavy objects through the air. They're usually designed to be operated by a human operator, who typically uses a remote controller and a beam to control the direction of movement of the crane.

Due to the fact that cranes are used for lifting and moving very heavy objects, they are powered by an internal combustion engine and electric motors.

Furthermore, all cranes have the maximum capacity of load they're able to lift at a particular point in time. In order to determine the rated or gross capacity of a crane and maintain safe operation, it is important to check its load capacity chart. The actual load a crane can lift is its net capacity and it must not be exceeded at any time, so as to avoid structural failure or overturning of the crane.

Hence, the best way to find the load capacity of a crane is to look at the load capacity chart in the cab.

The load can include rigging components, hooks, blocks, and other lifting equipment that is considered part of the load. The maximum load capacity of the crane is about 18 metric tons.

Hence the option C look at the chart is correct.

Learn more about the way to find the load capacity of a crane.

brainly.com/question/25884809.

Answer:                      

Explanation:

Answer:

I am not sure it's confusing

Answer:

Engine bearings are lubricated by motor oils constantly supplied in sufficient amounts to the bearings surfaces. Lubricated friction is characterized by the presence of a thin film of the pressurized lubricant

Explanation:

Answer: i believe it’s acoustics

Explanation:

Answer:

0.0371 kg/s.m

Explanation:

From the given information, let's have an imaginative view of the semi-cylinder; (The image is shown below)

Assuming the base surface of both ends of the cylinder is denoted by:

[tex]A_1 \ and \ A_2[/tex]

Thus, using the summation rule, the view factor [tex]F_{11[/tex] and [tex]F_{12[/tex] is as follows:

[tex]F_{11}+F_{12}=1[/tex]

Let assume the surface (1) is flat, the [tex]F_{11} = 0[/tex]

Now:

[tex]0+F_{12}=1[/tex]

[tex]F_{12}=1[/tex]

However, using the reciprocity rule to determine the view factor from the dome-shaped cylinder [tex]A_2[/tex] to the flat base surface [tex]A_1[/tex]; we have:

[tex]A_2F_{21} = A_{1}F_{12} \\ \\ F_{21} = \dfrac{A_1}{A_2}F_{12}[/tex]

Suppose, we replace DL for [tex]A_1[/tex] and

[tex]A_2[/tex] =  [tex]\dfrac{\pi D}{2}[/tex]

Then:

[tex]F_{21} = \dfrac{DL}{(\dfrac{\pi D}{2}) L} \times 1 \\ \\ =\dfrac{2}{\pi} \\ \\ =0.64[/tex]

Now, we need to employ the use of energy balance formula to the dryer.

i.e.

[tex]Q_{21} = Q_{evaporation}[/tex]

But, before that;  let's find the radian heat exchange occurring among the dome and the flat base surface:

[tex]Q_{21}= F_{21} A_2 \sigma (T_2^4-T_1^4) \\ \\ Q_{21} = F_{21} \times \dfrac{\pi D}{2} \sigma (T_2^4 -T_1^4)[/tex]

where;

[tex]\sigma = Stefan \ Boltzmann's \ constant[/tex]

[tex]T_1 = base \ temperature[/tex]

[tex]T_2 = temperature \ of \ the \ dome[/tex]

∴

[tex]Q_{21} = 0.64 \times (\dfrac{\pi}{2}\times 1.5) \times 5.67 \times 10^4 \times (1000^4 -370^4)\\ \\ Q_{21} = 83899.15 \ W/m[/tex]

Recall the energy balance formula;

[tex]Q_{21} = Q_{evaporation}[/tex]

where;

[tex]Q_{evaporation} = mh_{fg}[/tex]

here;

[tex]h_{fg}[/tex] = enthalpy of vaporization

m = the water mass flow rate

∴

[tex]83899.15 = m \times 2257 \times 10^3 \\ \\ m = \dfrac{83899.15}{ 2257 \times 10^3 }\\ \\ \mathbf{m = 0.0371 \ kg/s.m}[/tex]

The drying rate per unit length is 0.037 kg/S.m

Given data;

From the attached diagram, the surface 1 is flat, it is a view factor, f[tex]_1_1[/tex] = 0.

Applying summation rule and solving the view factor from the base surface A[tex]_1[/tex] to the cylindrical dome A[tex]_2[/tex].

[tex]f_1_1+f_1_2=1[/tex]

Put F[tex]_1_2=0[/tex]

[tex]0+f_1_2=1[/tex]

This makes [tex]f_1_2=1[/tex]

Applying reciprocal rule and solving the view factor from the cylindrical dome A[tex]_2[/tex] to the base surface A[tex]_1[/tex].

[tex]A_2F_2_1=A_1F_1_2\\F_2_1=(\frac{A_1}{A_2})F_1_2[/tex]

Where A is the area of the surface.

Substitute DL for A[tex]_1[/tex] and [tex]\frac{\pi D}{2}[/tex] for A[tex]_2[/tex]

[tex]F_2_1 = \frac{DL}{(\frac{\pi D}{2}})L *1 = \frac{2 }{\pi } =2/3.14 = 0.64[/tex]

Using the energy balance equation to the dryer,

[tex]Q_2_1=Q_e_v_a_p[/tex]

Let's calculate the radiation heat exchange between the dome and the base surface per unit length by using the equation below

[tex]Q_2_1=F_2_1A_2[/tex]δ[tex](T_2^4-T_1^4)[/tex]

[tex]Q_2_1= F_2_1 * \frac{\pi D}{2}[/tex]δ[tex](T_2^4-T_1^4)[/tex]

substitute the respective values into the equation

[tex]Q_2_1=0.64*(\frac{\pi }{2}*1.5)*5.67*10^-^8*(1000^4-370^4)\\Q_2_1=8.3899.15W/m[/tex]

Let's calculate the mass flow rate of water using the amount of heat required for drying up.

[tex]Q_2_1=Q_e_v_a_p\\Q_e_v_a_p=mh_f_g\\[/tex]

where [tex]h_f_g= 2257*10^3J/kg[/tex]

and this is the enthalpy of vaporization and mass flow rate of water.

[tex]83899.15=m*2257*10^3\\m=0.037kg/S.m[/tex]

The drying rate per unit length is 0.037kg/S.m

Learn more about mass flow rate here

https://brainly.com/question/24356835

https://brainly.com/question/24315432

Answer:

Resistance = 3 Ω

Explanation:

As we know that, By Ohm's Law

V = IR

where

V is the voltage in volt

I is the current in amps

R is the resistance in ohm

Now,

Given that,

V = 15 volts

I = 5 amps

So,

R = V/I

  = 15/5

 = 3 Ω

⇒R = 3 Ω

Answer:

medium sized ears

Explanation:

Incomplete question. The options read;

A. Tech A

B. Tech B

C. Both A and B

D. Neither A nor B.

Answer:

C. Both A and B

Explanation:

Technician B is correct because the technician highlighted valid reasons why draining the compressed air systems is important.

For example, since this system helps to absorb moisture or oil from storage areas they thus need to be drained periodically in other to allow for more absorption space.

Also, the reasons mentioned by Technician A are of course correct because it is generally believed that the application of lubricants such as oil helps to reduce wear and tear.