Type the correct answer in the box. Spell all words correctly. Elaine is an engineer. She has to create a prototype of a machine. To do this, she uses a technique where the production time of the prototype is reduced considerably with the help of a fast generation of 3D models. Which technique did she use? Elalne used the technique where the production time of the prototype is reduced considerably with the help of a fast generation of 3D models.​

Answer:

answer is

a)

3/4

Explanation:

In the last 5 meters of braking, you lose 3/4 of your speed.

Answer:

The answer is below

Explanation:

1)

[tex]R_{AB}=(500+500)||(500+500)\\\\R_{AB}=1000||1000\\\\R_{AB}=\frac{1000*1000}{1000+1000} \\\\R_{AB}=500\ \Omega[/tex]

2)

[tex]R_{AB}=1000\|(1000+1000+1000)\\\\R_{AB}=1000||3000\\\\R_{AB}=\frac{1000*3000}{1000+3000} \\\\R_{AB}=750\ \Omega[/tex]

3)

Because of the short, the resistance is zero.

[tex]R_{AB}=0[/tex]

4)

[tex]R_{AB}=940\ \Omega[/tex]

5)

[tex]R_{AB}=2200||2200||(2200+2200)\\\\R_{AB}=2200||2200||4400\\\\\frac{1}{R_{AB}}=\frac{1}{2200} +\frac{1}{2200} +\frac{1}{4400} \\\\\frac{1}{R_{AB}}=\frac{5}{4400}\\\\R_{AB}=880[/tex]

6)

[tex]R_{AB}=(220+100)||470||330\\\\R_{AB}=320||470||330\\\\\frac{1}{R_{AB}}=\frac{1}{320} +\frac{1}{470} +\frac{1}{330} \\\\R_{AB}=120.7\ \Omega[/tex]

Answer:

what is wrong with it and what is the question

Explanation:

tbm queria saber essa pergunta

Answer:

The limits of the hole size are;

The maximum limit of the hole diameter 0.255

The minimum limit of the hole diameter = 0.245

Explanation:

Tolerance is a standardized form of language that can be used to define the intended 'tightness' or 'clearance' degree between mating parts in a mechanical assembly process and in metal joining processes such as welding and brazing processes

In tolerancing, the size used in the description of a part is known as the nominal size while allowable variation of the nominal size that will still allow the part to function properly is known as the tolerance

A tolerance given in the form ±P is known as bilateral tolerancing, with the value being added to or subtracted from the nominal size to get the maximum and minimum allowable limits of the dimensions of the nominal size

Therefore;

The given nominal dimension of the hole diameter = 0.250

The bilateral tolerance of the dimension, = ±0.005

Therefore;

The maximum limit of the diameter of the hole = 0.250 + 0.005 = 0.255

The minimum limit of the diameter of the hole = 0.250 - 0.005 = 0.245

Answer:

to use cleaning tools safe its save to read what there made of its safe not to use to much of the product its also save to use gloves and goggles for some other products

Ans:

1.some families of farmers are poor so they are forced to cultivate on small lands.

2.farmers have not enough resources to keep good care of the crops.

3.land nowadays is so expensive that they afford a small piece of land to cultivate.

4.farmers need helpers when there are no helpers, the farmers need to make there land small in order to cultivate.

Explanation:

i was just able to write 4 sorry. :(

Answer:

Rapid Prototyping

Explanation:

The guy in the comments above gave the answer and i got it right on the test. Thank you my brother

Answer:

Service-entrance conductors can be spliced or tapped per 110.14, 300.5(E), 300.13, and 300.15 [230.46].

Explanation:

Service entrance conductors (aka, "service feed wire") run from the weather-head (exterior point of attachment) from the utility pole to the electric panel (usually the circuit breaker box). For most homes, the service entrance conductor will be located on or near the roof and tie into the overhead electrical lines.

Answer:

Amps, electrons

Explanation:

Amps, or amperes is the measure of electrons flowing though a wire per second.

1A = 6.24*10^18 electrons / second

Answer:

A break in the arrow is used to indicate the base material that needs to be beveled

A. Break in the arrow

Explanation:

In a weld that involves the welding of a joint that has a, a bevel, flare bevel, or J-groove, the side that requires beveling (chamfering) preparation in the welded joint before welding is indicated by an arrow having a definitive before pointing to the beveled member

However, the break in the arrow could excluded when the side to be chamfered is unmistakable

Therefore, the break in the arrow is the option that is used to indicate which of the material that is to be beveled.

Answer:

Explanation:

What Agricultural Engineers Do. ... Agricultural engineers attempt to solve agricultural problems concerning power supplies, the efficiency of machinery, the use of structures and facilities, pollution and environmental issues, and the storage and processing of agricultural products.