Answer:
2nd one
Explanation:
on edge 21
The option that identifies the engineer should choose the reverse engineering process in the following scenario is there will be changes to the existing product. The correct option is b.
What is reverse engineering?The distinction between the reverse engineering process and the engineering design process is quite slight. The engineering design process is a method that requires months of planning and design in order to provide a blueprint for a specific project.
The fundamental skill of learning to make something by working backward from an existing inspiration for your project is called reverse engineering.
Three contrasts are that the engineering design process is based more on mental and written learning than it is on physical learning (unlike the reverse engineering process).
Therefore, the correct option is b, There will be changes to the existing product.
To learn more about reverse engineering, refer to the link:
https://brainly.com/question/10175918
#SPJ2
A tank is filled with oil whose density is 850kg/m3. If the volume of the tank is 2.0m3, determine the amount of mass m in the tank
Answer:
1700 kg
Explanation:
Determine the total mass of the oil, m, by multiplying the density,
p= 850 kg/m3
to the volume, V = 2m3 or m=p x v.
m=pxv.
m= p x v = 850 kg / m3 x 2
m3 = 1700 kg
What value of filter capacitor is required to produce 1% ripple factor for a full wave rectifier having load resistance of 1.5kohm? Assume rectifier produces peak output of 18v
Answer:
Explanation:
The component has an exponentially distributed reliability with a mean of 2000 hours what is the probability that it will fail after 3000 hours?
Answer:
ABCDEFGHIJKLMNOPQRSTUVWXYZ
Which term is defined as the study of sound waves and their behaviors and interactions? propulsion acoustics hydraulics thermodynamics
Answer: i believe it’s acoustics
Explanation:
A circuit contains four 100 ohm resistors connected in series. If you test the circuit with a DMM you should read a total resistance value of
A. 250 ohms.
. B. 1000 ohms
C. 400 ohms
D. 100 ohms
Suppose a population of rabbits is introduced to an environment that has hot summers and extremely cold winters. Every winter, many rabbits die because of the cold and the lack of food. The rabbits have a range of ear sizes. Small Ears Medium Ears Large Ears Rabbits lose a lot of their body heat through their ears. Every winter, more of the large-eared rabbits die than the others. Every summer, more of the short-eared rabbits die than the others. At first, there are an equal number of rabbits with each size of ears. After several years, what will the frequency of ear sizes in the population be like?
Answer:
medium sized ears
Explanation:
Saul is testing an installation and discovers a short circuit. What's causing this?
A. High current
B. High voltage
C. Low voltage
D. Low resistance
Please help with these circuit questions
What could be used as another word for electrical potential?
A. Current
B. Wattage
C. Voltage
D. Power
Answer: C. Voltage
Explanation:
Here are some other words as well.
potential, voltage, potential drop, potential difference.
Answered by the ONE & ONLY #QUEEN aka #DRIPPQUEENMO!!!
HOPE THIS HELPED!!!
A dryer is shaped like a long semi-cylindrical duct of diameter 1.5 m. The base of the dryer is occupied with water-soaked materials to be dried. The base is maintained at a temperature of 370K, while the dome of the dryer is maintained at 1000 K. If both surfaces behave as blackbody, determine the drying rate per unit length experienced by the wet materials.
Answer:
0.0371 kg/s.m
Explanation:
From the given information, let's have an imaginative view of the semi-cylinder; (The image is shown below)
Assuming the base surface of both ends of the cylinder is denoted by:
[tex]A_1 \ and \ A_2[/tex]
Thus, using the summation rule, the view factor [tex]F_{11[/tex] and [tex]F_{12[/tex] is as follows:
[tex]F_{11}+F_{12}=1[/tex]
Let assume the surface (1) is flat, the [tex]F_{11} = 0[/tex]
Now:
[tex]0+F_{12}=1[/tex]
[tex]F_{12}=1[/tex]
However, using the reciprocity rule to determine the view factor from the dome-shaped cylinder [tex]A_2[/tex] to the flat base surface [tex]A_1[/tex]; we have:
[tex]A_2F_{21} = A_{1}F_{12} \\ \\ F_{21} = \dfrac{A_1}{A_2}F_{12}[/tex]
Suppose, we replace DL for [tex]A_1[/tex] and
[tex]A_2[/tex] = [tex]\dfrac{\pi D}{2}[/tex]
Then:
[tex]F_{21} = \dfrac{DL}{(\dfrac{\pi D}{2}) L} \times 1 \\ \\ =\dfrac{2}{\pi} \\ \\ =0.64[/tex]
Now, we need to employ the use of energy balance formula to the dryer.
i.e.
[tex]Q_{21} = Q_{evaporation}[/tex]
But, before that; let's find the radian heat exchange occurring among the dome and the flat base surface:
[tex]Q_{21}= F_{21} A_2 \sigma (T_2^4-T_1^4) \\ \\ Q_{21} = F_{21} \times \dfrac{\pi D}{2} \sigma (T_2^4 -T_1^4)[/tex]
where;
[tex]\sigma = Stefan \ Boltzmann's \ constant[/tex]
[tex]T_1 = base \ temperature[/tex]
[tex]T_2 = temperature \ of \ the \ dome[/tex]
∴
[tex]Q_{21} = 0.64 \times (\dfrac{\pi}{2}\times 1.5) \times 5.67 \times 10^4 \times (1000^4 -370^4)\\ \\ Q_{21} = 83899.15 \ W/m[/tex]
Recall the energy balance formula;
[tex]Q_{21} = Q_{evaporation}[/tex]
where;
[tex]Q_{evaporation} = mh_{fg}[/tex]
here;
[tex]h_{fg}[/tex] = enthalpy of vaporization
m = the water mass flow rate
∴
[tex]83899.15 = m \times 2257 \times 10^3 \\ \\ m = \dfrac{83899.15}{ 2257 \times 10^3 }\\ \\ \mathbf{m = 0.0371 \ kg/s.m}[/tex]
The drying rate per unit length is 0.037 kg/S.m
Given data;
Base temperature (T1) = 370KTemperature of the dome (T2) = 1000KF[tex]_1_2[/tex] = 1.5mD = 1.5mBoltzmann's constant (δ) = [tex]5.67 * 10 ^-^8 W/m^2.K^4[/tex]From the attached diagram, the surface 1 is flat, it is a view factor, f[tex]_1_1[/tex] = 0.
Applying summation rule and solving the view factor from the base surface A[tex]_1[/tex] to the cylindrical dome A[tex]_2[/tex].
[tex]f_1_1+f_1_2=1[/tex]
Put F[tex]_1_2=0[/tex]
[tex]0+f_1_2=1[/tex]
This makes [tex]f_1_2=1[/tex]
Applying reciprocal rule and solving the view factor from the cylindrical dome A[tex]_2[/tex] to the base surface A[tex]_1[/tex].
[tex]A_2F_2_1=A_1F_1_2\\F_2_1=(\frac{A_1}{A_2})F_1_2[/tex]
Where A is the area of the surface.
Substitute DL for A[tex]_1[/tex] and [tex]\frac{\pi D}{2}[/tex] for A[tex]_2[/tex]
[tex]F_2_1 = \frac{DL}{(\frac{\pi D}{2}})L *1 = \frac{2 }{\pi } =2/3.14 = 0.64[/tex]
Using the energy balance equation to the dryer,
[tex]Q_2_1=Q_e_v_a_p[/tex]
Let's calculate the radiation heat exchange between the dome and the base surface per unit length by using the equation below
[tex]Q_2_1=F_2_1A_2[/tex]δ[tex](T_2^4-T_1^4)[/tex]
[tex]Q_2_1= F_2_1 * \frac{\pi D}{2}[/tex]δ[tex](T_2^4-T_1^4)[/tex]
substitute the respective values into the equation
[tex]Q_2_1=0.64*(\frac{\pi }{2}*1.5)*5.67*10^-^8*(1000^4-370^4)\\Q_2_1=8.3899.15W/m[/tex]
Mass flow rateLet's calculate the mass flow rate of water using the amount of heat required for drying up.
[tex]Q_2_1=Q_e_v_a_p\\Q_e_v_a_p=mh_f_g\\[/tex]
where [tex]h_f_g= 2257*10^3J/kg[/tex]
and this is the enthalpy of vaporization and mass flow rate of water.
[tex]83899.15=m*2257*10^3\\m=0.037kg/S.m[/tex]
The drying rate per unit length is 0.037kg/S.m
Learn more about mass flow rate here
https://brainly.com/question/24356835
https://brainly.com/question/24315432
For the siphon shown in Figure, determine the flowrate out of the siphon and the absolute
pressure at the crest of the siphon assuming that there is no losses through the pipe.
2.00 m
Del
50-mm-diameter
Oil (s.g. =0.82)
5.00 m
Which type of engineering is more of an exploratory process that does not need to create a product that fits limitations and specifications?
reverse engineering
materials engineering
documentation process
engineering design process
Answer:
\❤)engineering design process(❤/
Explanation:
(♨️)BRAINLEIST PLEASE(♨️)
Tech A says that air tools and equipment require a regular application of a lubricating oil to reduce wear and tear. Tech B says that some compressed air systems use an inline water trap that needs to be drained periodically. Who is correct?
Incomplete question. The options read;
A. Tech A
B. Tech B
C. Both A and B
D. Neither A nor B.
Answer:
C. Both A and B
Explanation:
Technician B is correct because the technician highlighted valid reasons why draining the compressed air systems is important.
For example, since this system helps to absorb moisture or oil from storage areas they thus need to be drained periodically in other to allow for more absorption space.
Also, the reasons mentioned by Technician A are of course correct because it is generally believed that the application of lubricants such as oil helps to reduce wear and tear.
Does anyone know this
what type of power source is used for gmaw
Answer:
The GMAW process commonly uses a constant voltage power source (GMAW-CV) that allows for a relatively constant welding voltage output over a range of welding currents. For GMAW-CV the welder selects the wire feed speed (WFS) on the wire feeder unit and an appropriate voltage on the welding power supply.
ln a circuit a voltage of 15 volts is used to dereve a current of 5amps what is the resistance of the conductor
Answer:
Resistance = 3 Ω
Explanation:
As we know that, By Ohm's Law
V = IR
where
V is the voltage in volt
I is the current in amps
R is the resistance in ohm
Now,
Given that,
V = 15 volts
I = 5 amps
So,
R = V/I
= 15/5
= 3 Ω
⇒R = 3 Ω
WHAT PARTS OF THE BRAKE LAMP SYSTEM CAN FAIL? DESCRIBE HOW?
Help me ASAP please
Answer:
Explanation:
Brake systems are most likely to fail at the ends. One of the most common problems is a trailer lighting splitter is left on. With time and usage, the fuse can blow interrupting the signal path from the switch to the bulb.
Answered by the ONE & ONLY #QUEEN aka #DRIPPQUEENMO
HOPE THIS HELPED!!!
Which tool or device is an example of a pneumatic power system that uses compressed air to tighten or loosen an object? a jackhammer a lifting system a turbine an impact driver
Answer:
A jackhammer.
Explanation:
A jackhammer is a pneumatic device that was invented by William Mcreavy. Later, Mcreavy sold the patent of jackhammer to Charles Brady King. The tool is a combination of chisel and hammer. The tool is powered by compressed air to tighten or loosen an object. By using pressurized air, jackhammers help workers to drill and lossen an object.
Therefore, option A is correct.
Answer:
Impact Driver
Explanation:
Explain how the horsepower of a sports car can be improved.
Answer:
with turbo or nos
Explanation:
will anyone give me some food I am hungry
Answer:
ok
Explanation:
Answer:
yeah you will have it sir
Bending is defined as? A. the application of a load tending to distort a member in one direction. B. the application of opposing load with a very narrow specific area. C. the application of pushing load data application of pulling loads. E.application of twisting a load.
How are engine bearings lubricated?
Answer:
Engine bearings are lubricated by motor oils constantly supplied in sufficient amounts to the bearings surfaces. Lubricated friction is characterized by the presence of a thin film of the pressurized lubricant
Explanation:
Miriam is doing a measurement with her multimeter and the LCD is showing Hz. What's she measuring?
A. Resistance
B. Amplitude
C. Voltage
D. Frequency
Answer:
voltage
Explanation:
because it is used with a moving pointer to display readings.
What's the best way to find the load capacity of a crane? Select the best option Call the manufacturer Look at the load capacity chart in the cab Ask co-workers It's best determined by lifting a load
Answer:
Look at the load capacity chart in the cab
Explanation:
A crane can be defined as a large, tall metallic machine or equipment that is designed with a long horizontal arm (jib) used for the lifting and movement of very heavy objects through the air. They're usually designed to be operated by a human operator, who typically uses a remote controller and a beam to control the direction of movement of the crane.
Due to the fact that cranes are used for lifting and moving very heavy objects, they are powered by an internal combustion engine and electric motors.
Furthermore, all cranes have the maximum capacity of load they're able to lift at a particular point in time. In order to determine the rated or gross capacity of a crane and maintain safe operation, it is important to check its load capacity chart. The actual load a crane can lift is its net capacity and it must not be exceeded at any time, so as to avoid structural failure or overturning of the crane.
Hence, the best way to find the load capacity of a crane is to look at the load capacity chart in the cab.
The load can include rigging components, hooks, blocks, and other lifting equipment that is considered part of the load. The maximum load capacity of the crane is about 18 metric tons.
The load carried has made the crane in such as way that it can carry the load to certain levels. Hence they also provide the chart which says about the types and quantities of load.Hence the option C look at the chart is correct.
Learn more about the way to find the load capacity of a crane.
brainly.com/question/25884809.
Why is not adjust the depth of cut in the center of work piece in facing turning?
Answer:
I am not sure it's confusing
The radiation meter is showing radiation 2x as much as background. Is this a hot zone? If so why or why not?
Answer:
This is not a clear indication of the hot zone as the information of the radioactivity of the background is not provided clearly.
Explanation:
According to IAEA as well as NRCP, the hot area is defined on the basis of the radioactivity reading it shows instead of contrast or comparative reading from the background. The value of radiation activity which will be required to declare an area as hot zone is if it is greater than 0.1 mSv/h or [tex]1.5091\times 10^{29} kg^{-1} s^{-1}[/tex].
