Legal metrology would protect consumers from businesses that do not take measurements according to defined measuring regulations.

Answer:

The estimated batching production is 210 cy/hr

Explanation:

Given;

capacity of the batching chamber of the plant, Q = 12.5 cy

average batching cycle time, t = 3 min

plant efficiency, n = 84 %

The estimated batching production is calculated as efficiency of the machine multiplied by the production rate in hour. This is given by the solution below;

Batching production = (nQ )/ t

[tex]Batching \ production = 0.84(\frac{12.5 \ cy}{3 \ min} *\frac{60 \ min}{1 \ hr})\\\\ Batching \ production = 210 \ cy/hr[/tex]

Therefore, the estimated batching production is 210 cy/hr

Answer:

Computer science

Explanation:

Computer science is the most theoretical computing discipline, focusing mostly on finding new and better ways for computers to work.

The process of carrying out a specific computation through the design and construction of an executable computer program is known as computer programming.

Tasks like analysis, creating algorithms, and assessing the precision and resource use of those algorithms are all part of programming.

As we know,

The study of computing, robotics, and information is known as computer science. Algorithmic, computing theory, information theory, and automation are examples of academic areas in computer science.

Thus, computer science is the most theoretical computing discipline, focusing mostly on finding new and better ways for computers to work.

Learn more about computer programming here:

brainly.com/question/14618533

#SPJ2

Answer:

116,090 Btus

Explanation:

Answer:

72 MPa

Explanation:

Critical resolved shear stress = 36 MPa

calculate the maximum possible yield strength for a single crystal of the metal

first we have to express the critical resolved shear stress as

бy = 2т[tex]_{critical}[/tex]

given that the minimum stress needed to introduce yielding curve will occur  at Ψ = λ = 45

where : бy = yielding stress

             t[tex]_{critical}[/tex] = 36MPa

therefore the maximum possible yield strength

= (2) * (36)

= 72 MPa

Answer:

Your mobile phone has more computing power than the computers used for the Apollo 11 moon landing.

Mobile phones have to “work harder” to get a signal if you are in a moving vehicle.

The first mobile phone was made in 1973.

The first mobile phones that went on sale in 1983 cost nearly $4,000 each.

In 2012 Apple sold 340,000 phones per day.

4 out of 10 Brits admit to snooping on their partners phone.

Out of the 53% of snoopers that found incriminating evidence on their partner’s phone, 5% went on to terminate their relationship.

Waterproof mobile phones came to market because Japanese youngsters like to use them in the shower.

Apparently mobile phones have 18 times more bacteria on them than toilet handles!

Phubbing describes the act of snubbing someone by using your mobile phone in their company.

In 2015 more people died from taking selfies than shark attacks.

Teenagers that use a phone more than 2 hours a day increase their risk of depression and anxiety.

Nomobophobia is severe anxiety caused by the thought or act of losing your phone or running out of battery.

Explanation:

Answer:

I think 1 31/32

Answer:

Explanation:

I think I will say it is because most, if not all resistors have been made to standard already.

The value for the resistor that is chosen for two fixed arms from the Wheatstone Bridge have to be quite bear each other, as much as possible. The arm that moves and the other that doesn't move, their resistance values are made to be quite close as well. This makes the resistance of the arm that moves to be set somewhere in the middle, and as a result, the measurements don't exceed beyond the resistance range of the arm that moves.

I hope you understand?

Answer:

T = 3460 K

Explanation:

See attachment for calculation.

Since the temperature we have is above the melting point of the metal, then we can conclude that it is too high for the diffusion process to be possible.

Answer:

Explanation:

1. Checking your mirrors are very important because if someone screwed with them then it can mess up your driving.

2. Putting on your seat belt is a law so you must put it on and it can save your life one day.

Answer:

Speed V1 at the beginning of the skid  = 57.075 mph

Explanation:

Calculate the V1 speed at the beginning of the skid

V1 ( speed before brake was applied ) = ?

distance travelled by Vehicle 1 = 195 ft

curve tangent for vehicle 1 =  - 3% = - 0.03

coefficient of friction = 0.48

speed at Impact = 25 mph

To determine the V1 speed at the beginning of the skid we have to apply AASTHO

d1 = [tex]( \frac{VA^{2} - VA^{12} }{30(F+N)} )[/tex]

195 =  [tex](\frac{VA^2- 25^2}{30(0.48-0.03)} )[/tex]

Hence : VA = 57.075 mph

Answer:

mechanical engineering

Explanation:

Note, in the case of Patricia and Mathew, they both completed not a bachelor's degree but a certificate course, which does not meet the requirements of a master's degree program in an engineering college.

Furthermore, even though Tanya has a bachelor’s degree in chemical engineering it is less relevant to the field of Robotics.

But Nick who graduated in mechanical engineering (in other words having a bachelor in mechanical engineering) is most likely to be accepted in an engineering college for admission to a master’s degree program in robotics because he has a background in the field of Robotics.

Answer:

Resolution of Fourier transform = 2Hz

Explanation:

Given:

Sample signals = 16,384 samples/second

Number of data points = 8,192 oints

Find:

Resolution of Fourier transform

Computation:

Resolution of Fourier transform = fs / N

Resolution of Fourier transform = 16,384 / 8,192

Resolution of Fourier transform = 2Hz

Answer:

a Network Engineer (architect)

Explanation:

Indeed, as a Network Engineer, we would expect Nicole to be in charge of planning, setting up, and managing the software and hardware components of the computer networks so that they function as intended.

A Network Engineer therefore would be responsible for setting up the networking capabilities and policies that will govern the workstations when connected to the company network.

Answer:

- weather refers to short-term changes in the atmosphere

- climate describes what the weather is like over a long period of time in one area.

Answer:

1) The pressure difference is 4.207 kilopascals.

2) 2.5 pounds per square inch equals 5.093 inches of mercury and 5.768 feet of water.

Explanation:

1) We can calculate the gas pressure difference from the U-tube manometer by using the following hydrostatic formula:

[tex]\Delta P = \frac{S\cdot \rho_{w}\cdot g \cdot \Delta h}{1000}[/tex] (Eq. 1)

Where:

[tex]S[/tex] - Relative density, dimensionless.

[tex]\rho_{w}[/tex] - Density of water, measured in kilograms per cubic meter.

[tex]g[/tex] - Gravitational acceleration, measured in meters per square second.

[tex]\Delta h[/tex] - Height difference in the U-tube manometer, measured in meters.

[tex]\Delta P[/tex] - Gas pressure difference, measured in kilopascals.

If we know that [tex]S = 1.5[/tex], [tex]\rho_{w} = 1000\,\frac{kg}{m^{3}}[/tex], [tex]g = 9.807\,\frac{m}{s^{2}}[/tex] and [tex]\Delta h = 0.286\,m[/tex], then the pressure difference is:

[tex]\Delta P = \frac{1.5\cdot \left(1000\,\frac{kg}{m^{3}} \right)\cdot \left(9.807\,\frac{m}{s^{2}} \right)\cdot (0.286\,m)}{1000}[/tex]

[tex]\Delta P = 4.207\,kPa[/tex]

The pressure difference is 4.207 kilopascals.

2) From Physics we remember that a pound per square unit equals 2.036 inches of mercury and 2.307 feet of water and we must multiply the given pressure by corresponding conversion unit: ([tex]p = 2.5\,psi[/tex])

[tex]p = 2.5\,psi\times 2.037\,\frac{in\,Hg}{psi}[/tex]

[tex]p = 5.093\,in\,Hg[/tex]

[tex]p = 2.5\,psi\times 2.307\,\frac{ft\,H_{2}O}{psi}[/tex]

[tex]p = 5.768\,ft\,H_{2}O[/tex]

2.5 pounds per square inch equals 5.093 inches of mercury and 5.768 feet of water.

Answer:

[tex]7304g/cm^3[/tex]

Explanation:

Density is the mass per unit volume, it is usually measured in kg/m³.

The density of a crystal structure is given by:

[tex]\rho=\frac{mass\ of\ atoms\ in\ unit\ cell}{volume\ unit\ cell} =\frac{nA}{V_cN_A} \\\\\rho=density, n= number\ of\ atoms/unit=1\ atom/unit\ cell,A=atomic\ weight=70.4\ g/mol,N_A=avogadro\ constant=6.023*10^{23}atoms/mol,V=volume=2R^3=[2(0.126*10^{-8})]^3cm\\\\\rho=\frac{1*70.4}{[2(0.126*10^{-8})]^3*6.023*10^{23}} =7304g/cm^3[/tex]

Answer:

7.307g/cm^3

Explanation:

The other guy is mostly right but his conversion factor was off. It should be 1.26x10^-8 on the bottom

Answer:Modulus of Elasticity (E)-------- A

Explanation:

The modulus of elasticity, Young's modulus E is a measure of a material's stiffness or resistance to being elastically deformed when stressed or due to tension According to  Hook's law the modulus of elasticity is defined as the ratio of the stress to the strain and defined as the slope of its stress-strain region  in the stress and strain graph.

--The stiffer a material, the higher the elastic modulus and vice versa for a less stiff material.

it can be calculated with this formulae

Young’s modulus equation is E = tensile stress/tensile strain

= (FL) / (A X change in L)

where F = applied force,

L = initial length,

A = square area,

E = Young’s modulus in Pascals (Pa).

Answer:

carried courage buried

Explanation:

its Filipino

Answer:

It's equalization of the system

Explanation: If there was a leak it would likely leak all the time even if the car was turned off. Plus, a system leak bad enough to hear would drain the system of refrigerant very quickly and would no longer cool.

Answer:

kkklhfh254+326+-9643-5*/1546509866

"%&!83

Explanation:

Answer:

1. Industrial revolution was initiated or borne through the production of Steel

2. World War 1 led to the development of Tanks

Explanation:

The production of Steel through the Bessemer Process in the middle of the nineteenth century was a major technological development that spurred the Industrial revolution. This invention led to the widespread use of steel in the production of many things including vehicles and airplanes.

During the First World War in 1914, soldiers found the use of just their armaments in battle as not so productive. This led to the development of Tanks in 1915 that would continue moving towards the enemy even when being shot at.

Answer:

Visualization model

Explanation:

This type of model uses a computer to analyze and simulate data that require processing to enable presentation to users in a meaningful manner where even a layman could have a clue and understand the results expected. Through this model, results are presented in various forms such as plots of a the results against time for displaying relationships. For example a model that uses an animation could display results in various dimensions such as 2D and 3D ,and position in terms of orientation and position in respect to time.

Answer:

The correct answer is a prototype.

Explanation:

The prototype should be fully functional in order to test out the design, but aesthetics do not necessarily need to be considered yet. The prototype can allow constructive feedback from the client and team members, and it can be smaller than the eventual finished product. It can be used to “sell” an idea to a client.

Answer:

The answer is below

Explanation:

Given that:

x = 5 cm = 0.05 m, width (w) = 5 cm = 0.05 m, thickness (t) = 1 mm = 0.001 m, k = thermal conductivity = 200 W/mK, h = heat transfer coefficient = 22 W/m².K, Tb = base temperature = 40°C, T∞ = 20°C

[tex]m=\sqrt{ \frac{hp}{kA} }=\sqrt {\frac{22*(2*0.05+2*0.001)}{200*(0.05*0.001)}} =15\ m^{-1}\\\\\frac{T-T_{\infty}}{T_b-T_{\infty}} =e^{-mx}\\\\\frac{T-20}{40-20} =e^{-15*0.05}\\\\T-20=9.45\\\\T=29.45^oC\\\\The\ rate\ of\ heat\ loss\ is:\\\\\dot{Q}=\sqrt{hpkA}(T_b-T_{\infty})\\ \\\dot{Q}=\sqrt{22*(2*0.05+2*0.001)*200*0.05*0.001}*(40-20)\\\\\dot{Q}=3\ W[/tex]

Answer:

The answer is "150 [tex]\Omega[/tex]".

Explanation:

Its line length must be converted into wavelengths for the Smith chart to be used.

[tex]\to \beta = \frac{2 \pi }{\lambda } \\\\\to u_p = \frac{\omega }{\beta}\\\\\lambda =\frac{2 pi}{\beta} =\frac{2 \pi U_p}{\omega}=\frac{c}{\sqrt{\varepsilon_r f}}[/tex]

                        [tex]= \frac{3 \times 10^8}{ 2.25 \times (5 \times 10^9)}\\\\= \frac{3}{ 2.25 \times 5\times 10 }\\\\= \frac{3}{ 22.5 \times 5 }\\\\= \frac{3}{ 112.5}\\\\= 0.04 \ m.[/tex]

[tex]l =\frac{0.30 }{0.04 } \times \lambda[/tex]

  [tex]= 7.5 \lambda[/tex]

Because it is an integrated half-wavelength amount,

[tex]Z_{in} = Z_L = 150 \ \Omega[/tex]

Answer:

  no

Explanation:

No. More power is dissipated when the transistor is in its active region. In general, transistors in switching circuits are biased either "on" or "off". Time spent in the active region is minimized.

_____

On the other hand, speed can be enhanced if the transistors are active. So, it's a speed/power trade-off. Usually power is of more interest, particularly when there are millions of switching circuits. However, in certain applications, speed may be the priority, so the transistor will be biased in its active region.

Answer:

18 teeth/inch

Explanation:

Given that: i. driver gear has 8 teeth and diametral pitch of 6 teeth/inch.

                  ii. follower gear has 24 teeth.

Let the followers diametral pitch be represented by x.

Then,

8 teeth ⇒  6 teeth/inch

24 teeth ⇒ x teeth/inch

So that;

x = [tex]\frac{24 x 6}{8}[/tex]

   = [tex]\frac{144}{8}[/tex]

   = 18 teeth/inch

The diametral is 18 teeth/inch