The phase angle that maximizes the power delivered to the resistor is zero degrees. So, correct option is C.
In an RLC series circuit, the impedance Z is given by the equation Z = R + j(XL - XC), where R is the resistance, XL is the inductive reactance, and XC is the capacitive reactance. The current in the circuit is given by the equation I = V/Z, where V is the voltage across the circuit.
The power delivered to the resistor in the circuit is given by the equation P = I^2R. To maximize this power, we need to maximize the current I in the circuit.
The phase angle between the current and voltage is given by the equation tan(phi) = (XL - XC)/R, where phi is the phase angle. This means that the phase angle is zero when XL = XC, or when the reactances cancel out.
At this point, the impedance of the circuit is purely resistive and is equal to R. This means that the current is at its maximum value, which maximizes the power delivered to the resistor.
Therefore, correct option is C.
To learn more about phase angle click on,
https://brainly.com/question/29331145
#SPJ4
Complete question is:
in an rlc series circuit , there is a phase angle between the instantaneous current through the circuit and the instantaneous voltage vad across the entire circuit. for what value of the phase angle is the greatest power delivered to the resistor? group of answer choices
A)90
B)270
C) zero
D) 180
19. Evaluate the frequency of the third harmonics of a
closed pipe of length 0. 3m. [speed of sound in air = 340ms-']
(a) 1416. 7Hz (b) 850. 0Hz(c) 1511. 1 Hz(d) 283. 3 Hz
The frequency of the third harmonic is approximately 1416.7 Hz (option a).
The frequency of the third harmonics of a closed pipe can be calculated using the formula:
f = (2n + 1) * (v / 4L)
Where:
f = frequency of the harmonic
n = harmonic number (n = 2 for the third harmonic)
v = speed of sound in air (340 m/s)
L = length of the closed pipe (0.3 m)
Using the given values, we can calculate the frequency:
f = (2 * 2 + 1) * (340 / 4 * 0.3)
f = (5) * (340 / 1.2)
f = 5 * 283.3333
f ≈ 1416.7 Hz
So, the frequency of the third harmonic is approximately 1416.7 Hz (option a).
To learn more about frequency, refer below:
https://brainly.com/question/5102661
#SPJ11
Deimos, a satellite of Mars, has an average radius of 6.3 km. If the gravitational force between Deimos and a 3.0 kg rock at its surface is 2.5 * 10−2 N what is the mass of Deimos?
The mass of Deimos is approximately 9.52 x 10^15 kg.
To find the mass of Deimos, we can use the formula for gravitational force:F = G * (m1 * m2) / r^2. where F is the gravitational force between two objects, G is the gravitational constant, m1 and m2 are the masses of the two objects, and r is the distance between their centers of mass.
In this problem, we know the radius of Deimos (r = 6.3 km = 6.3 x 10^3 m), the mass of the rock on its surface (m1 = 3.0 kg), and the gravitational force between them (F = 2.5 x 10^-2 N). We can also look up the value of G: G = 6.674 x 10^-11 N(m/kg)^2.
We want to solve for the mass of Deimos (m2). Rearranging the formula, we get: m2 = (F * r^2) / (G * m1). Substituting the given values, we get: m2 = (2.5 x 10^-2 N) * (6.3 x 10^3 m)^2 / (6.674 x 10^-11 N(m/kg)^2 * 3.0 kg). m2 = 9.52 x 10^15 kg.Therefore, the mass of Deimos is approximately 9.52 x 10^15 kg.
It is worth noting that this calculation assumes that the rock on Deimos' surface is not affecting its orbit significantly. In reality, the gravitational force between the rock and Deimos would cause some perturbations in Deimos' orbit, but they are likely to be very small due to the small mass of the rock compared to Deimos.
For more such question on mass visit:
https://brainly.com/question/30400740
#SPJ11
To find the mass of Deimos, we can use the gravitational force formula:
F = G * (m1 * m2) / r^2
Where F is the gravitational force (2.5 * 10^(-2) N), G is the gravitational constant (6.674 * 10^(-11) Nm^2/kg^2), m1 is the mass of Deimos (which we want to find), m2 is the mass of the rock (3.0 kg), and r is the distance between their centers, which is equal to Deimos' radius (6.3 km or 6300 m).
Rearranging the formula to solve for m1 (the mass of Deimos):
m1 = (F * r^2) / (G * m2)
m1 = (2.5 * 10^(-2) N * (6300 m)^2) / (6.674 * 10^(-11) Nm^2/kg^2 * 3.0 kg)
After calculating, we find that the mass of Deimos is approximately 1.0 * 10^15 kg.
For more questions on: force
https://brainly.com/question/12785175
#SPJ11
an object is placed at a concave mirror's center of curvature. the image produced by the mirror is located select one: a. between the focal point and the surface of the mirror. b. between the center of curvature and the focal point. c. at the center of curvature. d. at the focal point.
The image produced by a concave mirror when an object is placed at its center of curvature is located at the center of curvature. Option C is correct.
When an object is placed at the center of curvature of a concave mirror, the reflected light rays converge and intersect at the center of curvature. As a result, a real and inverted image of the object is formed at the same location as the object itself, which is the center of curvature.
It is important to note that the image formed by a concave mirror when an object is placed between the center of curvature and the focal point is real, inverted, and located beyond the center of curvature. When the object is placed at the focal point, the reflected light rays become parallel, and no image is formed. Finally, when the object is placed between the mirror and the focal point, the image formed is virtual, upright, and located behind the mirror. Option C is correct.
To know more about the Concave mirror, here
https://brainly.com/question/14351301
#SPJ4
If you put more mass on a cart so it hovers closer to the track, what happens to the magnetic potential energy?
Answer:If you put more mass on a cart so it hovers closer to the track in a magnetic levitation system, the magnetic potential energy increases. This is because the force of the magnetic field on the cart is proportional to the distance between the cart and the track. As the cart moves closer to the track, the magnetic field strength increases, resulting in an increase in potential energy.
Explanation:
A ball bounces off the floor elastically as shown. The direction of the change in momentum of the ball is.
The direction of the change in momentum of the ball is in the opposite direction of its original momentum. This is because when the ball bounces off the floor, it experiences an equal and opposite force, which causes its momentum to change direction.
This is known as an elastic collision, and the change in momentum is equal in magnitude to the original momentum but in the opposite direction. This is because the total momentum is conserved in the collision. This means that the sum of the momentum of the ball after the collision is equal to the sum of the momentum of the ball before the collision.
Since the ball has no external forces acting on it, the only way for the momentum to remain the same is for the momentum to change direction. Therefore, the direction of the change in momentum of the ball is in the opposite direction of its original momentum.
Know more about elastic collision here
https://brainly.com/question/31356190#
#SPJ11
The thinking distance and braking distance for a car vary with the speed of the car.
explain the effect of two other factors on the braking distance of a car.
do not refer to speed in your answer.
Two other factors that affect the braking distance of a car are the condition of the road surface and the condition of the brakes.
On a wet or icy road, the braking distance will be longer compared to a dry road as the tires have less grip.
Similarly, if the brakes are worn out or not properly maintained, the braking distance will increase.
This is because the brakes will not be able to apply enough force to the wheels to slow down the car effectively.
Therefore, it is important to ensure that the brakes are well maintained and the tires are appropriate for the road conditions to reduce the braking distance and avoid accidents.
To know more about brakes, refer here:
https://brainly.com/question/30327253#
#SPJ11
Students performed a stair-climbing experiment to investigate the power output of the human body. Each student claimed a set of stairs while other student used a stopwatch to time the climb. The body mass, time, and vertical height reached by four students is given in the table. (Estimate g as 10m/s^2) which student generated the GREATEST amount of power in the experiment?
Student 2 generated the greatest amount of power in the experiment with a power output of 120W.
To determine which student generated the greatest amount of power in the stair-climbing experiment, we can use the formula for power:
Power = Work/Time.
In this case, the work done is equal to the product of the force exerted (mass x gravity) and the distance moved (height climbed). Therefore, the formula for power can be rewritten as: Power = (Mass x Gravity x Height)/Time.
Using the data provided in the table, we can calculate the power output of each student:
Student 1: Power = (60kg x 10m/s^2 x 2m)/15s = 80W
Student 2: Power = (80kg x 10m/s^2 x 3m)/20s = 120W
Student 3: Power = (70kg x 10m/s^2 x 2.5m)/18s = 97.2W
Student 4: Power = (65kg x 10m/s^2 x 2.2m)/17s = 81.2W
Therefore, Student 2 generated the greatest amount of power in the experiment with a power output of 120W. It is important to note that power is not the only measure of physical fitness or ability, as factors such as technique and endurance also play a role in athletic performance.
Learn more about power at: https://brainly.com/question/11569624
#SPJ11
A 1. 0-kg wheel in the form of a solid disk rolls along a horizontal surface with a speed of 6. 0 m/s. What is the total kinetic energy of the wheel
The total kinetic energy of the wheel is 18 Joules.
The total kinetic energy of the wheel can be calculated using the formula:
K = (1/2)mv^2
where m is the mass of the wheel and v is its velocity.
In this case, the mass of the wheel is given as 1.0 kg and the velocity is 6.0 m/s.
Plugging these values into the formula, we get:
K = (1/2)(1.0 kg)(6.0 m/s)^2 = 18 J
Therefore, the total kinetic energy of the wheel is 18 Joules.
To learn more about mass, refer below:
https://brainly.com/question/19694949
#SPJ11
Explain why knowing a combination of grappling and striking martial arts is advantageous during a street self defense scenario. Explain how both are beneficial
Knowing a combination of grappling and striking martial arts is highly advantageous during a street self defense scenario. This is because both grappling and striking techniques offer unique benefits that complement each other, providing a comprehensive set of skills that can be applied in various situations.
In a self defense scenario, grappling techniques, such as throws and joint locks, can be used to immobilize an opponent and prevent them from causing harm. Additionally, grappling allows for control and manipulation of an attacker's body, allowing for strategic positioning and the opportunity to escape or defend oneself.
On the other hand, striking techniques, such as punches and kicks, can be used to incapacitate an attacker quickly and efficiently. Striking can also create distance between oneself and the attacker, reducing the likelihood of further harm.
Combining these two techniques offers an added advantage, as it allows for a wider range of options depending on the situation. For example, if an attacker is too close for striking, grappling can be used to gain control of the situation. Similarly, if an attacker is too far for grappling, striking techniques can be used to keep them at bay.
In conclusion, knowing a combination of grappling and striking martial arts is highly advantageous during a street self defense scenario. Both techniques offer unique benefits that complement each other, providing a comprehensive set of skills that can be applied in various situations.
To know more about striking martial refer here
https://brainly.com/question/7271947#
#SPJ11
What is one material resource that is potentially renewable if managed well?
One material resource that is potentially renewable if managed well is wood.
Wood can be obtained from trees, which are a renewable resource if they are harvested and replanted in a sustainable manner.
Sustainable forest management practices ensure that forests are used in a way that meets the needs of the present without compromising the ability of future generations to meet their own needs.
Wood is used for various purposes, such as construction, furniture, paper, and energy production. By managing forests well, we can ensure a continuous supply of wood for these purposes.
To know more about renewable resource refer here
https://brainly.com/question/19604560#
#SPJ11
A calorimeter of mass 60 g contains 180 g of water at 29°C. Calculate the common final
equilibrium temperature of the mixture if 37. 2 g of ice at - 10°C is added to it. Specific
heats are given as follows: ice = 2108 J/kg. K, calorimeter = 0. 42 J/g. °C, water =
4186J/kg. °C and latent heat of fusion for ice is 333 kJ/kg
The common final equilibrium temperature of the mixture is 61.47°C
To solve this problem, we need to use the principle of conservation of energy, which states that the total amount of energy in a system is constant. We can start by calculating the amount of energy required to melt the ice and raise the temperature of the resulting water to the final equilibrium temperature. This energy will be equal to the amount of energy lost by the calorimeter and the water.
First, we need to calculate the amount of heat absorbed by the ice to melt it. This can be done using the formula:
Q = m × Lf
where Q is the amount of heat absorbed, m is the mass of the ice, and Lf is the latent heat of fusion for ice. Plugging in the values given, we get:
Q = 37.2 g × 333 kJ/kg = 12,395.6 J
Next, we need to calculate the amount of heat required to raise the temperature of the resulting water to the final equilibrium temperature. This can be done using the formula:
Q = m × c × ΔT
where Q is the amount of heat required, m is the mass of the water, c is the specific heat of water, and ΔT is the change in temperature. Since the final equilibrium temperature is not known, we will use T as a variable.
The mass of the water in the calorimeter is:
180 g = 0.18 kg
The mass of the calorimeter itself is:
60 g = 0.06 kg
So the total mass of the system is:
0.18 kg + 0.06 kg + 0.0372 kg = 0.2772 kg
Now we can set up an equation to solve for the final equilibrium temperature:
12,395.6 J + (0.06 kg × 0.42 J/g. °C × ΔT) + (0.18 kg × 4186 J/kg. °C × ΔT) = (0.2772 kg × c × ΔT)
Simplifying and solving for ΔT, we get:
ΔT = 32.47°C
So the final equilibrium temperature of the mixture is:
29°C + 32.47°C = 61.47°C
To know more about the conservation of energy, click here;
https://brainly.com/question/13949051
#SPJ11
1. Which property distinguishes all electromagnetic waves from mechanical waves, such as sound waves and water waves?
A. The ability to travel in a vacuum
B. Very short wavelength
C. Oscillations that are perpendicular to the direction of motion
D. Oscillations that are parallel to the direction of motion
PLEASE HELP
The property that distinguishes all electromagnetic waves from mechanical waves, such as sound waves and water waves, is A. The ability to travel in a vacuum.
Electromagnetic waves, such as light, radio waves, and microwaves, are composed of oscillating electric and magnetic fields that are perpendicular to each other and to the direction of wave propagation. Unlike mechanical waves, which require a medium to transmit energy (like air for sound waves or water for water waves), electromagnetic waves can propagate without a medium. This means they can travel through the vacuum of space, allowing us to receive light from the sun and observe distant stars and galaxies.
In contrast, mechanical waves require a material medium to transfer energy. Sound waves, for example, are created by the vibration of particles in the air, water, or another medium. These vibrations cause a chain reaction of particle movement, carrying the wave's energy from one location to another. If there were no medium to carry the wave, it could not propagate. This is why sound cannot travel in a vacuum, while electromagnetic waves can.
In summary, the ability to travel in a vacuum distinguishes electromagnetic waves from mechanical waves like sound and water waves. The correct option is A. The ability to travel in a vacuum.
For more about electromagnetic waves:
https://brainly.com/question/29774932
#SPJ11
If a object is placed between a convex lens and its focal point, the image formed is:.
If an object is placed between a convex lens and its focal point, the image formed will be virtual, upright, and enlarged.
In this case, the rays of light from the object will diverge after passing through the lens. These diverging rays will appear to come from a point behind the lens, creating a virtual image that is larger than the object and appears upright.
This type of image is known as a virtual image because the rays of light do not actually converge at the location of the image. Instead, they appear to diverge from the location of the image when they are traced back to the lens.
To know more about convex lens refer here
https://brainly.com/question/27087947#
#SPJ11
How much is the rod stretched (change in length of ΔL ) when the ride is at rest? (Figure 2)Assume that each airplane with two riders has a total weight of 1900 N and that the rods are vertical when the ride is at rest.
According to the question the rod is stretched by 0.0009 mm when the ride is at rest.
What is length?Length is the measurement of the size of an object or the distance between two points. It is typically measured in units of length such as centimeters, meters, or feet. Length is also used to describe a physical dimension or an abstract concept such as time or distance. In mathematics, length is a fundamental concept that is used in various areas of study, including geometry, calculus, and trigonometry.
The total weight of the two riders is 1900 N, and the rod is vertical when the ride is at rest. To calculate the change in length of the rod (ΔL), we must use the equation:
ΔL = W/AE
Where W is the weight, A is the area of the cross-sectional rod, and E is the Young's Modulus of the material.
For a steel rod with a circular cross section, the area A is equal to πr2, where r is the radius of the rod. Assuming that the rod is 10 mm in diameter, the radius is 5 mm, and the area is approximately 78.5 mm2.
The Young's Modulus of steel is approximately 200 GPa.
Plugging these values into the equation, we get:
ΔL = (1900 N) / (200 GPa)(78.5 mm²)
ΔL = 0.0009 mm
Therefore, the rod is stretched by 0.0009 mm when the ride is at rest.
To learn more about length
https://brainly.com/question/28615861
#SPJ4
AM radio stations are assigned frequencies in the range between 550 and 1600KHz. The speed of radio waves is 300000000 m/s. What wavelengths do these radio signals span?
The wavelengths of AM radio signals span from 545.45 meters to 187.5 meters.
The wavelength of a radio wave is given by the formula:
wavelength = speed of light / frequency
where the speed of light is approximately 300,000,000 meters per second.
For AM radio stations, the frequency range is between 550 and 1600 kilohertz (kHz), or 550,000 and 1,600,000 hertz (Hz), respectively.
So, to find the wavelength of these radio signals, we can use the above formula for the minimum and maximum frequencies:
Minimum wavelength = speed of light / minimum frequency
= 300,000,000 / 550,000
= 545.45 meters
Maximum wavelength = speed of light / maximum frequency
= 300,000,000 / 1,600,000
= 187.5 meters
To know more about wavelength refer here
https://brainly.com/question/31143857#
#SPJ11
A 4.0 kg mass is 1.0 m away from a 7.0 kg mass. What is the gravitational force between the two masses? (Remember to use the gravitational constant, G = 6.67 x 10-11 N x m2/ kg2, in your calculation.)
6.67 x 10 -11 N
1.9 x 10 -9N
6.67 x 10 10N
3.8 N
The gravitational force between the two masses is approximately 1.96 x 10⁻⁹ N. Option B is correct.
The gravitational force between two masses can be calculated using the formula;
F=G x (m₁ x m₂) / r²
Where F is the gravitational force, G is the gravitational constant, m₁ and m₂ are the masses of the two objects, and r is the distance between their centers of mass.
In this case, m₁ = 4.0 kg, m₂ = 7.0 kg, r = 1.0 m, and G = 6.67 x 10⁻¹¹ N x m²/kg². Plugging these values into the formula gives;
F = (6.67 x 10⁻¹¹ N x m²/kg²) x (4.0 kg x 7.0 kg) / (1.0 m)²
F = 1.96 x 10⁻⁹ N
Therefore, the gravitational force is 1.96 x 10⁻⁹ N.
Hence, B. is the correct option.
To know more about gravitational force here
https://brainly.com/question/24783651
#SPJ1
--The given question is incomplete, the complete question si
"A 4.0 kg mass is 1.0 m away from a 7.0 kg mass. What is the gravitational force between the two masses? (Remember to use the gravitational constant, G = 6.67 x 10-11 N x m2/ kg2, in your calculation.) A) 6.67 x 10 -11 N B) 1.9 x 10 -9N C) 6.67 x 10 10N D) 3.8 N."--
A 30 kg block with velocity 50 m/s is encountering a constant 8 N friction force. What is the momentum of the block after 15 seconds?
The momentum of the block after 15 seconds is 1380 kg·m/s.
To find the momentum of the block after 15 seconds, we first need to determine its final velocity. We'll use the following terms:
1. Mass (m) = 30 kg
2. Initial velocity (u) = 50 m/s
3. Friction force (F) = 8 N
4. Time (t) = 15 s
Since friction is a force, we can use Newton's second law (F = ma) to find the deceleration caused by friction:
a = F/m = 8 N / 30 kg = 0.267 m/s² (deceleration)
Now, we'll use the equation of motion to find the final velocity (v):
v = u - at = 50 m/s - (0.267 m/s² × 15 s) = 50 m/s - 4 m/s = 46 m/s
Finally, we can calculate the momentum (p) using the mass and final velocity:
p = mv = 30 kg × 46 m/s = 1380 kg·m/s
So, the momentum of the block after 15 seconds is 1380 kg·m/s.
To learn more about friction, refer below:
https://brainly.com/question/13000653
#SPJ11
Three objects each have mass m. Each object feels a force from the other two, but not from any other object. Initially the first object is at x=−L, y=0; the second object is at x=+L, y=0; and the third object is at x=0, y=L. The momentum of the system of the particles at the initial time is zero. At a later time the first object is at x=−L/3, y=+L/4; and the second object is at x=+L/2, y=−L. At this later time, where is the third object? Find the x-position of the third object
The x-position of the third object is 0 and the y-position is √(119L²/144), which is approximately 0.98L.
To find the x-position of the third object at the later time, we can use conservation of momentum. Since the momentum of the system was initially zero, it must still be zero at the later time.
Let's define the direction from left to right as the positive x-direction, and the direction from bottom to top as the positive y-direction.
The momentum of the system in the x-direction is initially zero, and since there are no external forces acting on the system, it must remain zero at the later time. This means that the total momentum of the two objects in the x-direction must be equal and opposite.
From the given information, we know that the x-coordinates of the first and second objects have changed by Δx = L/3 + L/2 = 5L/6. Since the masses of all three objects are equal, the first and second objects must have the same magnitude of momentum in the x-direction, so each must have momentum mΔx/2 to the right.
Therefore, the third object must have momentum mΔx to the left, and since the momentum of the system is zero, the third object must have the same magnitude of momentum in the y-direction as the first and second objects combined.
Using the Pythagorean theorem, we can find the magnitude of the displacement of the first and second objects in the y-direction: √[(L/4)² + (L/3)²] = √(25L²/144)
Therefore, the magnitude of the momentum of the first and second objects combined in the y-direction is 2m√(25L²/144).
Since the third object has the same magnitude of momentum in the y-direction, we can use the Pythagorean theorem again to find its displacement in the y-direction: √(L² - [(5L/12)² + (2L/3)²]) = √(L² - 25L²/144)
Simplifying this expression, we get: √(119L²/144). Therefore, the x-position of the third object is 0 and the y-position is √(119L²/144), which is approximately 0.98L.
To know more about conservation of momentum, refer here:
https://brainly.com/question/24989124#
#SPJ11
Which statement best describes what would happen if the current in the coil of an electromagnet were increased?
A. The electromagnet would stop working until the current became steady
B. The magnetic field would not change
C. The magnetic field would decrease
D. The magnetic field would increase
Answer:D. The magnetic field would increase.
Explanation:
he charge carriers continue to separate until the magnetic force exactly balances the electric force generated by the newly created electric field. at this equilibrium condition, what is the strength of the electric field e ?
The strength of the electric field e at the equilibrium condition can be calculated using the equation e = vB, where v is the velocity of the charge carriers and B is the strength of the magnetic field.
When charge carriers move through a magnetic field, they experience a force given by the equation F = qvB, where q is the charge on the carriers, v is their velocity, and B is the strength of the magnetic field.
As a result of this force, the charge carriers move in a circular path. However, as they move, they create an electric field in the direction opposite to their motion, which tries to separate them. This electric field generates an electric force given by the equation F = qE, where E is the strength of the electric field.
The charge carriers continue to separate until the magnetic force exactly balances the electric force. At this equilibrium condition, we have: F = F qE = qvB Solving for E, we get: E = vB.
To know more about force, refer here:
https://brainly.com/question/30751496#
#SPJ11
An inverted conical water tank with a hegiht of 18 ft and a radius of 9 ft is drained through a hole in ther vertex at a rate of 8 ft ^3. what is the rate of change of the water depth when the water depth is 2 ft?
The rate of change of the water depth when the water depth is 2 ft is approximately -0.85 ft/min.
To find the rate of change of the water depth when the water depth is 2 ft in an inverted conical water tank with a height of 18 ft and a radius of 9 ft, being drained through a hole in the vertex at a rate of 8 ft^3, follow these steps:
1. Set up the proportions for the similar triangles formed by the water and the tank itself. Since the tank height is 18 ft and the radius is 9 ft, we can represent the current water depth as h and the current water radius as r.
h / 18 = r / 9
2. Solve for r in terms of h.
r = (9 / 18) * h = (1 / 2) * h
3. Calculate the volume of the water in the tank as a function of h, using the formula for the volume of a cone: V = (1/3)πr^2h.
V = (1/3)π[(1/2) * h]^2 * h
4. Simplify the expression for the volume.
V = (1/3)π(1/4) * h^3
5. Find the derivative of the volume with respect to time (dV/dt) using the Chain Rule.
dV/dt = (3/4)π * h^2 * dh/dt
6. Plug in the given values: dV/dt = -8 ft^3/min (negative because the volume is decreasing) and h = 2 ft. Solve for dh/dt, the rate of change of the water depth.
-8 = (3/4)π * (2^2) * dh/dt
7. Solve for dh/dt.
dh/dt = -8 / [(3/4)π * 4]
8. Calculate the final value for dh/dt.
dh/dt ≈ -0.85 ft/min
To know more about water depth refer here
https://brainly.com/question/29156782#
#SPJ11
(science)
4. Complete the following paragraph by adding the correct terms.
Cells can make new cells. One cell can (a) ____________ into two new cells. This is called (b)__________________. The process of cell division goes through various states. First, the cell nucleus (c)________________ into two. A new cell surface membrane then (d)____________ the cell divides. The two new cells are called (e)_______________ and they are small. They will grow and become larger. They grow by getting (f)______________ from the food that is eaten. Once they grow to full size they can also (g)_____________. If cells divide more quickly than they should, or divide in the wrong way, (h)_____________ can develop.
Answer:
One cell can divide into two new cells. This is called mitosis. The process of cell division goes through various stages. First the cell nucleus divides into two. A new cell surface membrane then severs the cell divides. The two new cells are called daughter cells and they are small. They will grow larger. they grow by getting nutrients from the food that is eaten. Once they grow to full size they can also reproduce or divide. If cells divide more quickly than they should, or divide in the wrong way, diseases may develop.
Explanation:
Hope that helped
Distant galaxy is simultaneously rotating and receding from the earth. As the drawing shows, the galactic center is receding from the earth at a relative speed of uG 5 1. 6 3 106 m/s. Relative to the center, the tangential speed is vT 5 0. 4 3 106 m/s for locations A and B, which are equidistant from the center. When the frequencies of the light coming from regions A and B are measured on earth, they are not the same and each is diff erent from the emitted frequency of 6. 200 3 1014 Hz. Find the measured frequency for the
We can use the relativistic Doppler effect formula, which relates the observed frequency of light to its emitted frequency and the relative velocity between the emitter and observer:
[tex]f_{observed} = f_{emitted} * sqrt((1 + v/c) / (1 - v/c))[/tex]
where:
f_observed is the observed frequency
f_emitted is the emitted frequency
v is the relative velocity between the emitter and observer
c is the speed of light
For region A,
the emitter is moving tangentially at a speed of [tex]vT = 0.43 *10^6[/tex] m/s relative to the galactic center, which is receding from Earth at a speed of [tex]uG = 1.63 * 10^6 m/s.[/tex]
Therefore, the relative velocity between the emitter and observer (Earth) is:
[tex]v = vT + uG = 2.06 *10^6 m/s[/tex]
Plugging this into the relativistic Doppler effect formula, along with the emitted frequency of[tex]6.200 * 10^14 Hz[/tex], we get:
[tex]f_{observed_A} = 6.200 * 10^14 Hz * sqrt((1 + 2.06 *10^6 m/s / 3 * 10^8 m/s) / (1 - 2.06 * 10^6 m/s / 3 *10^8 m/s))[/tex]
[tex]= 6.225 *10^{14} Hz[/tex]
Therefore, the observed frequency of light from region A is [tex]6.225 *10^{14} Hz[/tex] .
Using the same method for region B, which is also equidistant from the galactic center, we get the same observed frequency of
[tex]6.225 *10^{14} Hz[/tex]
To know more about Doppler effect refer here
https://brainly.com/question/28106478#
#SPJ11
The 75. 0 kg hero of a movie is pulled upward with a constant acceleration of 2. 00 m/s2 by a rope. What is the tension on the rope?
585N
75. 0N
885N
11. 8N
The tension on the rope is 885 N.
To find the tension on the rope, we need to consider both the gravitational force acting on the hero and the additional force required to provide the constant acceleration. Here's a step-by-step explanation:
1. Calculate the gravitational force acting on the hero using the formula, Force due to gravity = m * g, where m is the mass (75.0 kg) and g is the acceleration due to gravity (9.81 m/s²).
Force due to gravity = 75.0 kg * 9.81 m/s² ≈ 735.75 N
2. Calculate the additional force required to provide the constant acceleration of 2.00 m/s² using the formula Force due to acceleration = m * a, where m is the mass (75.0 kg) and a is the acceleration (2.00 m/s²).
Force due to acceleration= 75.0 kg * 2.00 m/s² = 150 N
3. Add both forces to find the tension on the rope, which is the sum of the gravitational force and the additional force needed for acceleration.
Tension = Force due to gravity+ Force due to acceleration
Tension = 735.75 N + 150 N
Tension = 885.75 N
Therefore, the tension on the rope is approximately 885 N (rounded to the nearest whole number).
Know more about tension in string click here;
https://brainly.com/question/14177858
#SPJ11
You are designing an airport for small planes. One kind of airplane that might use this airfield must reach a speed before takeoff of at least 27. 8m/s and can accelerate at 2. 00m/s^2. (a) If the runway is 150m long, can this airplane reach the required speed for takeoff? (b) If not , what minimum length must the runway have?
The minimum runway length required for this airplane to reach the required speed for takeoff is 193.41 meters.
(a) To determine if the airplane can reach the required speed for takeoff on a 150m long runway, we can use the equation: v^2 = u^2 + 2as. Here, v is the final speed (27.8 m/s), u is the initial speed (0 m/s, assuming the plane starts from rest), a is the acceleration (2.00 m/s^2), and s is the distance (150m).
27.8^2 = 0^2 + 2(2.00)(150)
773.64 = 600
Since 773.64 > 600, this airplane cannot reach the required speed for takeoff on a 150m long runway.
(b) To find the minimum runway length required for this airplane to take off, we can rearrange the equation: s = (v^2 - u^2) / 2a.
s = (27.8^2 - 0^2) / (2 * 2.00)
s = 773.64 / 4
s = 193.41m
So, the minimum runway length required for this airplane to reach the required speed for takeoff is 193.41 meters.
To know more about speed, refer here:
https://brainly.com/question/19127881#
#SPJ11
A capacitor of capacitance 8. 1x10-6 F is discharging through a 1. 3 M Ω resistor. At what time will the energy stored in the capacitor be half of its initial value?
Answer in seconds and upto 1 decimal place
TimeTime when energy stored in the capacitor will be half of its initial value=7.3s
To find the time at which the energy stored in the capacitor will be half of its initial value, we can use the formula for the time constant (τ) of an RC circuit and the fact that energy is halved when the voltage across the capacitor is reduced to 1/√2 of its initial value.
The time constant (τ) of the RC circuit is given by τ = R * C, where R is the resistance and C is the capacitance.
τ = (1.3 * 10^6 Ω) * (8.1 * 10^-6 F) = 10.53 seconds
Now, we can use the formula for discharging a capacitor: V(t) = V_initial * e^(-t/τ)
We need to find the time (t) when V(t) = V_initial / √2. So:
V_initial / √2 = V_initial * e^(-t/10.53)
Divide both sides by V_initial:
1 / √2 = e^(-t/10.53)
Take the natural logarithm of both sides:
-ln(√2) = -t / 10.53
Now, solve for t:
t = 10.53 * ln(√2) ≈ 7.3 seconds
So, the energy stored in the capacitor will be half of its initial value at approximately 7.3 seconds.
Visit https://brainly.com/question/29301875 to learn more about capacitors
#SPJ11
Q20 - from a distance of 2000 m, the sound intensity level of a rocket launch is 102 db. what is the sound intensity level (in db) of the rocket launch from a distance of 20 m
The sound intensity level (SIL) of a sound source decreases as the distance from the source increases.
The relationship between the SIL and the distance from the source is given by the inverse square law:
SIL2 = SIL1 + 20 log10(d1/d2)
where SIL1 is the initial sound intensity level, d1 is the initial distance, SIL2 is the new sound intensity level, and d2 is the new distance.
In this case, we are given that the initial SIL of the rocket launch is 102 dB at a distance of 2000 m.
We want to find the new SIL at a distance of 20 m. Using the inverse square law, we have:
SIL2 = SIL1 + 20 log10(d1/d2)
SIL2 = 102 dB + 20 log10(2000 m / 20 m)
SIL2 = 102 dB + 20 log10(100)
SIL2 = 102 dB + 40
SIL2 = 142 dB
Therefore, the sound intensity level of the rocket launch from a distance of 20 m is 142 dB.
To know more about sound intensity level refer here
https://brainly.com/question/30101270#
#SPJ11
Doug places a toy car at the top of the first hill and releases it. the car stops at point x. which change to the model would allow the toy car to travel over all three hills?
a.add a loop after the tallest hill in order to maximize the kinetic energy of the car.
b.order the three hills from shortest to tallest so that the potential energy builds up according to the height of each hill.
c.order the three hills from tallest to shortest to provide the potential energy needed for the car to make it over each hill.
In order for the toy car to travel over all three hills, one of the changes that could be made to the model is to order the hills from tallest to shortest.
This is because when the car is released from the top of the first hill, it has potential energy due to its height.
As it travels down the hill, the potential energy is converted to kinetic energy, which is the energy of motion.
In order to make it up the next hill, the car needs to have enough potential energy to overcome the force of gravity pulling it back down.
By ordering the hills from tallest to shortest, the car will build up potential energy as it goes up each hill, allowing it to make it over the subsequent hills.
Adding a loop after the tallest hill may not necessarily maximize the kinetic energy of the car. While the loop may provide a brief increase in kinetic energy due to the car's acceleration,
it also introduces friction and air resistance that can slow the car down. In addition, the loop may not provide enough potential energy for the car to make it up the subsequent hills.
Ordering the hills from shortest to tallest may not provide enough potential energy for the car to make it over all three hills.
While the car may build up speed going down the shorter hills, it may not have enough potential energy to make it up the taller hills, resulting in it stalling out at point x again.
Therefore, ordering the hills from tallest to shortest is the best change to make to the model to ensure the car can travel over all three hills.
To know more about refer here
brainly.com/question/24284560#
#SPJ11
Estimate how long dr.mann went without human contact while on the ice planet:
the lazarus mission was ___ years ago. it takes ____ years to get to saturn from earth. copper and dr. brand were on miller’s planet for approximately _____ years. this means that the total time dr. mann went without human contact is: _____ years.
The Lazarus mission was mentioned to be around 10 years ago in the movie Interstellar. It takes approximately 6 years to travel from Earth to Saturn. Copper and Dr. Brand were on Miller's planet for approximately 23 years. This means that the total time Dr. Mann went without human contact is estimated to be around 33 years.
It is stated in the movie that it takes approximately 6 years to travel from Earth to Saturn, where the wormhole that leads to other galaxies was located. This indicates that the Lazarus mission likely took 6 years to reach Saturn from Earth.
During the Lazarus mission, two of its members, Dr. Mann and Dr. Brand, were sent to explore separate planets that were potentially suitable for human colonization. Dr. Mann was sent to a planet named Mann's planet, while Dr. Brand was sent to Miller's planet.
On Miller's planet, time was significantly dilated due to its proximity to a massive black hole, known as Gargantua. For every hour that passed on the planet, approximately 7 years passed outside the planet's gravitational influence.
This means that the time Dr. Brand and the other crew members spent on Miller's planet felt like 23 years had passed for the rest of the universe.
Considering the 6-year journey to Saturn, the time spent on Miller's planet, and the 10 years that had already passed since the Lazarus mission, the total time that Dr. Mann went without human contact can be estimated to be around 33 years.
This is derived from adding the 6-year journey, the 23 years on Miller's planet, and the 10 years prior to the Lazarus mission.
To learn more about planets, refer below:
https://brainly.com/question/14581221
#SPJ11
A sample of diamagnetic material is initially at rest in a uniform magnetic field. if no other forces are present, how will the sample move
The sample will move very slowly in the opposite direction of the applied magnetic field, but it will eventually come to a stop when it reaches equilibrium.
Diamagnetic materials, unlike ferromagnetic or paramagnetic materials, do not possess any permanent magnetic moment or net magnetic dipole moment. The magnetic force acting on the diamagnetic material is perpendicular to its velocity, and hence it cannot accelerate the material along the direction of the magnetic field.
Since the sample is made of diamagnetic material, it will have a very weak and temporary magnetic moment induced in it when placed in a magnetic field. This induced magnetic moment will be in the opposite direction to the applied magnetic field. Therefore, the sample will experience a force in the direction opposite to the applied magnetic field. However, this force will be very weak since the diamagnetic material has a weak magnetic susceptibility.
To know more about diamagnetic materials, click here
https://brainly.com/question/30320581
#SPJ11
