i need help asap !

Work output has a force of 5 N and distance of 5 m. Work input has a force of 10 N and distance of 10 m. What is the efficiency?
100%

25%

125%

0.25%

Answers

Answer 1

Answer:

the answer is 100%!

your welcome


Related Questions

A block of density 8.9g/cm³ measures 5cm by 2cm, Given that the force of gravity is 10N/kg. Determine the maximum pressure

Answers

Answer:

Maximum pressure = 4450 N/m²

Explanation:

We'll begin by calculating the volume of the block. This can be obtained as follow:

Volume (V) = 5 cm × 3 cm × 2 cm

V = 30 cm³

Next, we shall determine the mass of the block. This can be obtained as follow:

Density = 8.9 g/cm³

Volume = 30 cm³

Mass =?

Density = mass /volume

8.9 = mass / 30

Cross multiply

Mass = 8.9 × 30

Mass = 267 g

Next, we shall covert 267 g to Kg.

1000 g = 1 Kg

Therefore,

267 g = 267 g × 1 Kg / 1000

267 g = 0.267 Kg

Thus, the mass of the block is 0.267 Kg

Next, we shall determine the force.

Force of gravity (g) = 10 N/Kg

Mass (m) = 0.267 Kg

Force (F) =?

F = mg

F = 0.267 × 20

F = 2.67 N

Next, we shall determine the minimum area since we are trying to obtain the maximum pressure. This can be obtained as follow:

Minimum area = 3 cm × 2 cm

Covert each measurement to metre (m) by dividing each measurement by 100

Minimum area = 0.03 m × 0.02 m

Minimum area = 0.0006 m²

Finally, we shall determine the maximum pressure. This can be obtained as follow:

Force (F) = 2.67 N

Minimum area = 0.0006 m²

Maximum pressure =?

Maximum pressure = Force /minimum area

Maximum pressure = 2.67 / 0.0006

Maximum pressure = 4450 N/m²

The elements in which section of the periodic table are the most stable and rarely react with other elements?
А metals
B metalloids
С noble gases
D nonmetals ​

Answers

I think it is A if wrong sorry

1.) Cameron loads a wheelbarrow full of dirt. She then holds up both handles and begins to push it across her yard. The push Cameron uses to move the wheelbarrow is an example of
trajectory

motion

dynamics

force

2.) Jeremy is pushing his two children on a set of swings. He gives his daughter a push and she swings about three feet high. Jeremy gives his son the same push, but he only swings about two feet high. What could account for the difference in how high the kids got?

Jeremy's daughter has more mass, so it takes less force to get her into the air.
Jeremy's son has more mass, so it would take more force to reach the same height as his daughter.
Jeremy's son has less mass, so it would take more force to reach the same height as his daughter.
Jeremy's daughter has more mass, so she accelerates faster than his son.

Answers

Answer:

C (Force)

Explanation:

Cmon we should all know dis

Answer:

force and Jeremy's son has more mass

Explanation:

pushing requires force and the son moves less

Which choice Not a direct risk of eating a diet too high in sugar? 1 diabetes 2 weight gain 3 tooth decay 4 weight loss

Answers

Answer:

4 weight loss

Explanation:

Please ans fast I will mark brainliest

For sure

Answers

Well for starters, that means that the air in the sky is very cold, and has a lower temperature. Since it is super dark, it is colder than the polar bear.

The polar bear is cold. Not as cold as the sky, and not as warm as the mouth and eyes, but it is still very cold. This is probably because it lives in a snowy and cold climate.

The polar bears eyes and mouth are warm. This is because, the spots where the eyes, mouth, and nose are is a very light shade. This concludes that those spots on the polar bear are warm.

use the following terms in the same sentence magnet magnetic force and magnetic pole

Answers

Answer:

The electrically charged gas particles are affected by magnetic forces.

For the past eleven years, the Sun's north geographic pole has also been home to its north magnetic pole

Explanation:

Planetesmals are made from

Answers

A planetesimal is an object formed from dust, rock, and other materials. According to the planetesimal hypothesis, when a planetary system is forming, there is a protoplanetary disk with materials from the nebulae from which the system came. This material is gradually pulled together by gravity to form small chunks.

Brainliest or a thank you please :)) <3

PLEASE help its timed..

Which statement describes how a machine can help make work easier?

A)It can put out more force than the input force by decreasing the distance over which force is applied.
B) It can increase the amount of work performed if the output force is in the same direction as the input force.
C) It can apply a greater output force over a greater distance compared to the input force and distance.
D) It can increase the distance over which output force acts by applying less output force than input force.​

Answers

Answer:

D

Explanation:

by increasing the distance through which force is applied, by changing the direction of force applied or by multiplying force of speed of the energy applied

When serving you start on the right and must hit to which designated area?

- right side you are looking at
- left side you are looking
- any place over the net

(pickle ball)

Answers

Bygggggfsfgggggggvvv

you can serve to anyplace over the net

If you are in a car that stops suddenly, what does your body continue to do?


Answers

Answer:

If the passengers were not wearing their seat belts:, then the passengers in motion would continue in motion. Assuming a negligible amount of friction between the passengers and the seats, the passengers would likely be propelled from the car and be hurled into the air. Once they leave the car, the passengers becomes projectiles and continue in projectile-like motion.

If they were: Any passengers in the car will also be decelerated to rest if they are strapped to the car by seat belts. Being strapped tightly to the car, the passengers share the same state of motion as the car. As the car accelerates, the passengers accelerate with it; as the car decelerates, the passengers decelerate with it; and as the car maintains a constant speed, the passengers maintain a constant speed as well.

I got this from https://www.physicsclassroom.com

What is happening when an oxygen molecule is formed from two separate oxygen atoms?

Answers

Two from each oxygen atom. For examples of covalent bonding are water (H2O), and carbon dioxide (CO2). Covalent compounds are mostly gases or liquids with low melting points.

This is graded help hurry pls

Answers

first one I think. Sorry if your get it wrong but it’s a temporary magnet so I’m really confident with the first.

A book is resting on the floor. It has 25 J of energy. A student lifts the book and places it on the top shelf of a bookshelf. The student uses 200 J of energy to lift the book onto the shelf. How much energy does the book have at the top of the shelf?
A.Exactly 25 J
B. About 225 J
C. At least250 J
D.Negative 175 J PLSS QUICK (3 minutes at most) ILL GIVE 70 POINTS AND BRAINLIEST (FOR CORRECT ANSWER)

Answers

Answer and Explanation:

A. Exactly 25 J.

This is because the 25 J of energy that is holding down the book will always be the same, unless another force is being applied to hit to either make it heaver for a combined force of J energy, or something is lifting it, which will subtract the force of J of energy whilst moving.

#teamtrees #PAW (Plant And Water)

How much force is required to move a electron through an electric field with strength of 1.375 x 10^19 N/C?

Answers

Answer:

The magnitude of the force required to move the electron through the given field is 2.203 N

Explanation:

Given;

The field strength of the electron, E = 1.375  x 10¹⁹ N/C

charge of electron, q = 1.602 x 10⁻¹⁹ C

The magnitude of the force required to move the electron through the given field is calculated as follows;

F = Eq

F = (1.375  x 10¹⁹ N/C) (1.602 x 10⁻¹⁹ C)

F = 2.203 N

Therefore, the magnitude of the force required to move the electron through the given field is 2.203 N

help meeeeeeeeeeee
what is the rheostat and what its ruleeee??​

Answers

Answer:

Rheostat, adjustable resistor used in applications that require the adjustment of current or the varying of resistance in an electric circuit. The rheostat can adjust generator characteristics, dim lights, and start or control the speed of motors.

Explanation:

Un cuerpo lleva una velocidad de 122k por hora y de golpe frena reduciendo su velocidad a 50km por hora en un instante de tiempo de 4,5 segundos y la fuerza de frenado es de 1200n, ¿cual será su masa?

Answers

Answer:

La masa del objeto es 270.027 kilogramos.

Explanation:

Asumamos que el cuerpo decelera a tasa constante, entonces podemos calcularlo por medio de la siguiente ecuación cinemática:

[tex]a = \frac{v-v_{o}}{t}[/tex] (1)

Donde:

[tex]v_{o}[/tex] - Velocidad inicial, en metros por segundo.

[tex]v[/tex] - Velocidad final, en metros por segundo.

[tex]t[/tex] - Tiempo, en segundos.

[tex]a[/tex] - Deceleración, en metros per segundo al cuadrado.

Si sabemos que [tex]v_{o} = 33.889\,\frac{m}{s}[/tex], [tex]v = 13.889\,\frac{m}{s}[/tex] y [tex]t = 4.5\,s[/tex], entonces la deceleración experimentada por el cuerpo es:

[tex]a = \frac{v-v_{o}}{t}[/tex]

[tex]a = -4.444\,\frac{m}{s^{2}}[/tex]

Por las Leyes de Newton, tenemos que la masa del cuerpo se calcula a partir de la siguiente expresión:

[tex]m = \frac{F}{a}[/tex] (2)

Donde:

[tex]m[/tex] - Masa, en kilogramos.

[tex]F[/tex] - Fuerza de frenado, en newtons.

Si sabemos que [tex]F = -1200\,N[/tex] y [tex]a = -4.444\,\frac{m}{s^{2}}[/tex], entonces la masa del cuerpo es:

[tex]m = \frac{F}{a}[/tex]

[tex]m = 270.027\,kg[/tex]

La masa del objeto es 270.027 kilogramos.

The picture below shows a wheelbarrow. Using a wheelbarrow can make it easier to lift a heavy object by
A. changing the direction of the input force.
B. reducing the amount of input force needed to lift the object.
C. decreasing the distance over which the input force is applied.
D. reducing the weight of the object.

Answers

Answer:

B IS CORRECT

Explanation:

reason why ink is most likely to ooze out of a pen when one is up in an airplane​

Answers

Answer:

Because in higher altitudes atmospheric pressure is low

4. An automobile gasoline engine is able to do 225 J of useful work with each stroke of its
pistons. If the engine has an efficiency of 29%, what is the amount of work that must be done on
the pistons in the engine?

Answers

[tex]\mathfrak{\huge{\orange{\underline{\underline{AnSwEr:-}}}}}[/tex]

Actually Welcome to the concept of Efficiency.

We know that, efficiency is given as,

E (eta) = Output work / Input Work

hence, here, E = 29% and Output work = 225

hence, 29% = 29/100 in real..

hence, the work done on piston is given as,

29/100 = 225/I

therefore, I = 225*100/29 ==> I = 22500/29 ==> I = 775.8 joules

hence, the work done on the pistons is 775 J

5 examples of electrical energy

Answers

Answer:

its very simple this list the items that you have in your house that have electric energy

Explanation:

These 2 processes cause watersheds to change.

Answers

Tsunami and water bender those are 2 like avatars

Answer:

Change is an integral component of the watershed. The wide variations in river and stream flow regularly change shorelines, stream channels and stream corridors. Upland areas of watersheds also undergo changes due to ecological succession, disease, competition, human activity and other factors.

Explanation:

A book is placed on a table and a bike moves on a road.

Which statement is correct?

Both the book and the bike have kinetic energy.
Both the book and the bike have potential energy.
The book has potential energy and the bike has kinetic energy.
The book has kinetic energy and the bike has potential energy.

Answers

The book has potential energy and the bike has kinetic.

kinetic energy is energy possessed when a object is in motion. The bike is moving. Therefore, it has kinetic energy. The book isn't moving. Hopefully that helped

A king orders a gold crown having a mass of 0.5 kg. When it arrives from the metalsmith, the volume of the crown is found to be 185 cm3. Is the crown made of solid gold?

Answers

Answer:

The crown is not made of solid gold.  

Explanation:

Density ρ = M/V.  M and V are given.

The density of the crown is (0.5 kg)/(185 cm3) * (106 cm3)/(1 m3) = 2.7*103 kg/m3.

Give me two examples of a pushing force and two examples of a pulling force:

Answers

Answer:

A pushing force example could be a button, like on a keyboard.

Another example would be a piston.

An example of a pulling force could be a lever.

Another example could be rope.

Hope this helps! c:

Why should Mike repeat this investigation?
Mike needs to make sure that all the skateboards are not affected by friction.
Mike needs to have more than one set of numbers to make an accurate graph
The investigation needs multiple trials to determine which board is the control.
The investigation needs to be repeated several times to have the most accurate data.

Answers

Answer:

D

Explanation:


A dog sits on a flat surface. If the dog has a mass of 13 kg, what is the normal force acting on it?
85 N
13 N
127 N
41 N

Answers

Answer:

127

Explanation:

f(n)=mg

(13)*(9.81)

127.4N

What could be the average human density? Justify?

Answers

Answer:

985 kg/m3

Explanation:

The average density of the human body is 985 kg/m3 k g / m 3 , and the typical density of seawater is about 1020 kg/m3 k g / m 3 .

Explanation:

the worldwide human population density is around 7,500,000,000 ÷ 510,000,000 = 14.7 per km2 (38 per sq. mi.). If only the Earth's land area of 150,000,000 km2 (58,000,000 sq. mi.) is taken into account, then human population density is 50 per km2 (129 per sq.

If the vehiche has a speed of 24.0 m/s at point a what is the force of the track on the vehicle at this point?

Answers

Question:

A roller-coaster vehicle has a mass of 500 kg when fully loaded with passengers.  If the vehicle has a speed of 20.0 m/s at point A, what is the force exerted by the track on the vehicle at this point?

See attachment

Answer:

33700 Newton

Explanation:

Given

[tex]m = 500kg\\v = 24.0m/s\\r=10m[/tex]

First, we determine the forces acting on mass m.

They are: the force exerted by the track (Fn) and the weight of the vehicle (W)

So, the net force is:

[tex]F_{net} = F_n - W[/tex]

[tex]W=mg[/tex]

So:

[tex]F_{net} = F_n - mg[/tex]

Make Fn the subject

[tex]F_n = F_{net} + mg[/tex]

Fnet is calculated as:

[tex]F_{net} = F_c = \frac{mv^2}{r}[/tex] --- i.e. the centripetal force

So:

[tex]F_n = F_{net} + mg[/tex]

[tex]F_n = \frac{mv^2}{r} + mg[/tex]

[tex]F_n = \frac{500 * 24^2}{10} + 500 * 9.8[/tex]

[tex]F_n = 28800 + 4900[/tex]

[tex]F_n = 33700N[/tex]

A 8.0-g bullet with an initial velocity of 115.0 m/s lodges in a block of wood and comes to rest at a
distance of 4.0 cm. Assume the bullet undergoes a constant negative acceleration; it slows at a
constant rate.
a. How much time does it take for the bullet to stop?
b. What is the impulse on the woodblock?
c. What is the average force experienced by the block?

Answers

A. When your fire a bullet into the air, it typically takes between 20 and 90 second for it to come down,depending on the angle it was fired at,its muzzle velocity and caliber.

give the relation of speed of sound with the density and temperature​

Answers

Answer:

The greater the density of a medium, the slower the speed of sound. This observation is analogous to the fact that the frequency of a simple harmonic motion is inversely proportional to m, the mass of the oscillating object.

Air molecules have more energy at higher temperatures, which means they vibrate faster. This allows the sound waves to also travel faster because they are propelled by collisions between the molecules

Other Questions
What does it mean to short, or sell short a stock Write a program to display MPH (Miles per Hour). Create a function to calculate the MPH. Ask the user for the number of miles driven and the number of minute it took to drive that many miles. Validate that both the number of miles and the number of minutes is a positive, non-zero number. Pass both the number of miles and the number of minutes to the function, and have the function return the MPH. Find the surface area of the rectangular prism.2 cm5 cm10 cm 1.Charlie buys two circular pizzas.The first pizza has a 12- The second pizza has ainch diameter14-inch diameter.How much greater, in square inches, is the area of the second pizza than the first pizza?Round your answer to the nearest tenth What is number 61 and a step by step explaination please? Hurry The mass of a standard hockey puckmust be at least 156 grams. What isthis weight in kilograms just this last one left How do you spell these sentences to French? im almost done with this hw. plz help!!! give explanation if you actually know the answer so ik u dont just want points Which figures can have all of the properties shown below Activity 1: Lines and Curves - Maps of LifeMATERIALS NEEDED: Pen, pencil or colored pencilsDirections:1. Recall some of your remarkable childhood memories.2. Using the diagram below sketch or draw the places that have been a part of yourlife and are of interest to the members of your family. Example: From your house,church, malls, parks and school.3. Answer the questions below and write your answer on the space provided.8881 Developmental psychology is the field that primarily studies how humans grow and develop.Please select the best answer from the choices providedOF Old Man Warner's dialogue in the following passage (paragraph 32) mainly suggests... Used to be a saying about 'Lottery in June, corn be heavy soon.' First thing you know, we'd allbe eating stewed chickweed and acorns. There's always been a lottery," he added petulantly.Bad enough to see young Joe Summers up there joking with everybody."A. the power of a tradition like the lotteryB. that he is much wiser than the other villagersC. that the lottery is necessary for the village's survivalD. that he is the story's villain Identify two causes and three political effects of the Great Depression Explain in detail how low density polyethylene is made 4) You are making a batch of cookies. Each batch uses 3 cups of flour and will give 7 servings. Youare going to multiply your recipe to offer more servings, so you use 11 cups of flour. How manyservings will you actually be able to offer?a. 22b. 2531d. 38C.rolexing and upsetting. For at that time I had already Select the words that include the Latin root tract.distractinspectorattractionintermissionHELP I have 130 L of gas in a piston at a temperature of 250C. If I cool the gasuntil the volume decreases to 85 L, what will the temperature of the gas be? Which expression is equivalent to 5c + 3c? 9y - 2x = 0 in slope intercept form.