In order to calculate the line voltage of a wye-connected three-phase system, you must multiply 1.73 by the phase voltage.
What is Phase Voltage?
In a three-phase power system, phase voltage is the voltage measured between any one phase and the neutral point. The neutral point in a wye-connected system is the point at which the three phases are joined together. There is no neutral point in a delta-connected system.
In a wye-connected system, the line voltage is calculated as follows:
3 x Phase Voltage = Line Voltage
Where "3" is the square root of three, which is roughly 1.73.
Therefor, to calculate the line voltage, multiply the phase voltage by 1.73, or the square root of 3.
Learn more about Phase Voltage here: https://brainly.com/question/29445057
#SPJ1
a coil of a resistance 30 and inductance 0.08h are connected to supply of 240v, 50hz calculate in impedance
The impedance of a coil of a resistance 30 and inductance 0.08h connected to supply of 240v, 50hz is about 39.11 ohms.
What does a coil with a 0.5 H inductance carry?The current flowing through a coil with an inductance of 0.5 H varies consistently from 0 to 10 A in 2s. The coil's generated emf is expressed as (in volts). 10. 5.
R = 30 ohms for resistance
L = 0.08 H for inductance
V = 240V is the supply voltage
F is equal to 50 Hertz.
We can use the following formula to determine the inductive reactance Xl:
Xl = 2πfL
Xl = 25.12 ohms because Xl = 2 3.14 50 0.08
We can now determine the coil's impedance Z:
Z = (R2 + Xl2) Z = (30+25.12) Z = (900+630.54)
Z = √1530.54
Z is roughly 39.11 ohms.
To know more about impedance visit:
https://brainly.com/question/29853108
#SPJ9
what item did a pair of inmates use to dig their way out of a virginia jail?
Two inmates at a Virginia jail used a metal bar and a piece of wire to dig their way out.
The pair had been held at the facility awaiting trial on charges including burglary, grand larceny, and other offenses.
They managed to create a hole in the wall of their cell and then burrowed their way out of the jail's perimeter fence. The escape was discovered during a routine security check.
Law enforcement officials launched a manhunt and eventually located the escapees, who were returned to custody.
The jail is now reviewing its security protocols and taking steps to prevent similar incidents in the future.
Learn more about security protocol at
https://brainly.com/question/9561645
#SPJ11
List and explain 10 software and 10 hardware components of a computer
10 Software Components:
Operating System
Device Drivers
Antivirus Software
Web Browsers
Media Players
Word Processors
Spreadsheet Programs
Presentation Software
Email Clients
Virtualization Software
10 Hardware Components:
CPU (Central Processing Unit)
RAM (Random Access Memory)
Hard Disk Drive (HDD)
Solid State Drive (SSD)
Motherboard
Power Supply Unit (PSU)
Graphics Processing Unit (GPU)
Sound Card
Network Interface Card (NIC)
Monitor
Software components refer to the programs that run on a computer system. An operating system is the core software component that manages hardware resources and provides a user interface. Device drivers enable the operating system to communicate with hardware devices.
Antivirus software is used to protect the system from malware threats. Web browsers allow users to browse the internet, while media players allow users to play audio and video files.
Word processors, spreadsheet programs, and presentation software are used for creating documents, spreadsheets, and presentations, respectively. Email clients are used to manage emails, and virtualization software enables multiple operating systems to run on a single computer.
Hardware components refer to the physical components that make up a computer system. The CPU is the brain of the computer, responsible for executing instructions. RAM is used for storing data that is currently in use by the system. The HDD and SSD are used for long-term storage of data.
The motherboard is the main circuit board that connects all components. The PSU provides power to the system. The GPU is responsible for processing graphics. The sound card provides audio output, while the NIC provides network connectivity.
The monitor is used for displaying output from the system.
For more questions like Antivirus click the link below:
https://brainly.com/question/14313403
#SPJ11
technician a says that unwanted resistance in a circuit can cause a fuse or circuit breaker to blow. technician b says that a short-circuit could result in the load never turning off. who is correct?
Both technicians A and B are correct, but they are describing different scenarios that can lead to a fuse or circuit breaker blowing.
1)Technician A is referring to the presence of unwanted resistance in a circuit. Resistance is a measure of how much a material resists the flow of electric current. In a circuit, resistance can be caused by factors such as corroded wires, loose connections, or damaged components. When unwanted resistance is present in a circuit, it can lead to a buildup of heat, which can cause the fuse or circuit breaker to blow. This is because the fuse or breaker is designed to prevent excessive heat and current from damaging the circuit or causing a fire.
2)Technician B is describing a short-circuit, which occurs when a wire or component in a circuit comes into contact with another wire or component that it should not be touching. When a short-circuit occurs, the resistance in the circuit drops to almost zero, causing a surge of current to flow through the circuit. This surge can cause the load to never turn off, even if the switch or other control mechanism is turned off. In some cases, the surge can also cause the fuse or circuit breaker to blow, as it tries to protect the circuit from the excessive current.
In summary, both technicians are correct, but they are describing different scenarios that can cause a fuse or circuit breaker to blow. Unwanted resistance can cause a buildup of heat, while a short-circuit can cause a surge of current. It's important to identify and address both issues to ensure safe and reliable operation of electrical circuits.
For such more questions on circuit breaker
https://brainly.com/question/14971898
#SPJ11
Using a compound interest of 10%, find the equivalent uniform annual cost for a proposed machine that has a first cost of P120,000 an estimated salvage value of P35,000 and an estimated economic life of 10 years. Annual maintenance will amount to P2,500 a year and periodic overhaul costing P5,000 each will occur at the end of the fourth and eight year
The equivalent uniform annual cost for the proposed machine is P26,212.25.
To calculate the equivalent uniform annual cost, we need to add up all the costs and salvage value and then calculate the equivalent annual payment over the economic life of the machine using the compound interest formula.
In this case, the total cost is P142,500 (P120,000 first cost + P25,000 maintenance + P10,000 overhaul - P13,500 salvage value). Using a compound interest rate of 10%, the equivalent uniform annual cost is P26,212.25.
The equivalent uniform annual cost provides a way to compare the costs of different machines or projects with different cash flows over their economic life. It represents an equal annual payment that would result in the same total cost as the proposed machine.
By calculating the equivalent uniform annual cost, we can determine if the machine is a good investment in terms of cost and benefit.
For more questions like Cost click the link below:
https://brainly.com/question/30045916
#SPJ11
Water is the working fluid in a Rankine cycle. Steam enters the turbine at 1400 lbf/in. 2 and 1000°F. The condenser pressure is 2 lbf/in. 2 Both the turbine and pump have isentropic efficiencies of 85%. The working fluid has negligible pressure drop in passing through the steam generator. The net power output of the cycle is 1 × 109 Btu/h. Cooling water experiences a temperature increase from 60°F to 76°F, with negligible pressure drop, as it passes through the condenser. Determine for the cycle (a) the mass flow rate of steam, in lb/h. (b) the rate of heat transfer, in Btu/h, to the working fluid passing through the steam generator. (c) the thermal efficiency. (d) the mass flow rate of cooling water, in lb/h
The mass flow rate of steam and cooling water is 8963 lb/h and 6.25x10^7 lb/h respectively whereas the rate of heat transfer is 1.307x10^7 Btu/h and thermal efficiency is 76.56%.
(a) To determine the mass flow rate of steam, we need to use the equation for mass flow rate:
mass flow rate = net power output / ((h1 - h2) * isentropic efficiency)
where h1 is the enthalpy of the steam entering the turbine and h2 is the enthalpy of the steam leaving the turbine and entering the condenser.
Using a steam table, we can find that h1 = 1474.9 Btu/lb and h2 = 290.3 Btu/lb. Plugging in the values and converting Btu/h to lb/h, we get:
mass flow rate = (1x10^9 Btu/h) / ((1474.9 - 290.3) * 0.85) = 8963 lb/h
Therefore, the mass flow rate of steam is 8963 lb/h.
(b) The rate of heat transfer to the working fluid passing through the steam generator can be calculated using the equation:
Q = mass flow rate * (h1 - h4)
where h4 is the enthalpy of the fluid leaving the condenser. Using a steam table, we can find that h4 = 46.39 Btu/lb. Plugging in the values, we get:
Q = (8963 lb/h) * (1474.9 - 46.39) = 1.307x10^7 Btu/h
Therefore, the rate of heat transfer to the working fluid passing through the steam generator is 1.307x10^7 Btu/h.
(c) The thermal efficiency of the cycle is given by:
thermal efficiency = net power output / heat input
where heat input is the rate of heat transfer to the working fluid passing through the steam generator. Plugging in the values, we get:
thermal efficiency = (1x10^9 Btu/h) / (1.307x10^7 Btu/h) = 76.56%
Therefore, the thermal efficiency of the cycle is 76.56%.
(d) To determine the mass flow rate of cooling water, we can use the equation:
rate of heat transfer to cooling water = mass flow rate of cooling water * specific heat of water * (T2 - T1)
where T1 and T2 are the inlet and outlet temperatures of the cooling water. Plugging in the values, we get:
1x10^9 Btu/h = mass flow rate of cooling water * 1 Btu/lb°F * (76°F - 60°F)
mass flow rate of cooling water = (1x10^9 Btu/h) / (16 Btu/lb°F) = 6.25x10^7 lb/h
Therefore, the mass flow rate of cooling water is 6.25x10^7 lb/h.
Learn more about Fluid mechanics at:
https://brainly.com/question/17123802
#SPJ11
A coil having a resistance of 10 ohms and an inductance of 4 H is switched across a 20W dc source. Calculate (a) time required by the current to reach 50% of its final steady value, (b) value of the current after 0. 5 second
(a) The time constant of the circuit can be calculated as:
τ = L/R = 4/10 = 0.4 seconds
At t = τln(2), the current will have reached 50% of its final steady value. Therefore:
t = τln(2) = 0.4ln(2) ≈ 0.277 seconds
(b) The current in the circuit can be calculated using the formula:
i(t) = (V/R)(1 - e^(-t/τ))
At t = 0.5 seconds, we have:
i(0.5) = (20/10)(1 - e^(-0.5/0.4))
≈ 1.98 amps
Therefore, the value of the current after 0.5 seconds is approximately 1.98 amps.
How the atmosphere will react when there is vertical (upward) motion of air
Vertical motion of air causes changes in atmospheric conditions. As air rises, it cools, and as it falls, it warms.
What happens to the atmosphere when air moves upward?As air rises, it experiences a decrease in pressure, which causes it to expand and cool. This cooling can lead to the formation of clouds and precipitation, as the moisture in the air condenses.
As the air continues to rise, it eventually reaches a point where the temperature and pressure are too low for it to continue rising, and it begins to sink back towards the ground. This sinking air can cause warming and drying of the atmosphere, which can lead to clear skies and dry conditions.
Learn more about Precipitation
brainly.com/question/20925010
#SPJ11
A horizontal pipe carries fluid in fully developed turbulent flow. The static pressure difference measured between two sections is 750 psi. The distance between the sections is 15 ft, and the pipe diameter is 3 in. Calculate the shear stress, Tw, that acts on the walls
The shear stress acting on the walls of the pipe is 6.25 psi.
To calculate the shear stress, Tw, acting on the walls of the pipe, we can use the equation:
Tw = (dp/dx) × (D/4)
Where dp/dx is the static pressure gradient, D is the diameter of the pipe, and Tw is the shear stress.
Given that the static pressure difference is 750 psi and the distance between the sections is 15 ft, we can calculate the static pressure gradient as:
dp/dx = (750 psi) / (15 ft) = 50 psi/ft
Also, the diameter of the pipe is given as 3 in, which is equivalent to 0.25 ft.
Substituting these values into the equation, we get:
Tw = (50 psi/ft) × (0.25 ft/2) = 6.25 psi
In fully developed turbulent flow, the fluid particles move in random directions and interact with each other, creating eddies and vortices. This results in high fluid velocity and shear stress along the walls of the pipe. The shear stress is the force per unit area acting parallel to the wall, and it is important in designing and analyzing the strength and stability of pipelines and other fluid transport systems.
You can learn more about shear stress at: brainly.com/question/14418799
#SPJ11
The first step when using object-oriented design is to
The first step when using object-oriented design (OOD) is to identify and define the key components, called classes, within the system. This process involves understanding the problem domain, breaking it down into manageable parts, and defining the relationships and interactions among these parts.
Classes represent real-world entities or concepts and have attributes and methods. Attributes describe the properties or characteristics of a class, while methods define the actions or behaviors that a class can perform. To establish these classes, you should analyze the requirements and consider any existing constraints or limitations.
Once the classes are defined, you'll need to determine their relationships, which are typically represented using inheritance, aggregation, and association. Inheritance is a way for one class to inherit the attributes and methods of another, while aggregation and association describe the "has-a" and "uses-a" relationships between classes, respectively.
As you proceed with OOD, it's essential to focus on modularity, encapsulation, and abstraction. Modularity refers to the separation of functionality into independent, interchangeable modules. Encapsulation is the practice of bundling data and methods within a class, restricting access to certain parts of the object. Abstraction is the simplification of complex systems by presenting only the essential features and hiding implementation details.
In conclusion, the first step in OOD is to identify classes, define their attributes and methods, and establish relationships among them, while adhering to principles of modularity, encapsulation, and abstraction. This process lays the foundation for effective and efficient software development.
Learn more about object-oriented design (OOD) here: https://brainly.com/question/30174085
#SPJ11
Tech a says that when replacing the clock spring, you should turn it all the way to either end and then install it in the steering column. tech b says that clock springs are used to return the steering wheel to its centered position. who is correct
Both technicians are partially correct, but they are describing different aspects of the clock spring's function.
Technician A is correct in stating that the clock spring should be turned all the way to either end before installation. This is to ensure that the clock spring is properly centered and has the correct amount of tension to function properly.
Technician B is also correct in stating that the clock spring is used to return the steering wheel to its centered position. The clock spring is responsible for maintaining electrical connections to components such as the horn and airbag while allowing the steering wheel to turn freely. It does this by using a coiled spring that can rotate with the steering wheel while maintaining electrical contact.
Therefore, both technicians are correct, but they are describing different aspects of the clock spring's function and installation process.
Learn more about Automotive technology at:
https://brainly.com/question/30925950
#SPJ11
POWER ELECTRONICS OCTINOV 2017 69) (1) Using the transistor analogy, show that the anode Current (IA) for SCR Is given by: In = aw₂ Ig + ICBOIT ICBDR Where a, and as are transistor 1- (x₁+x₂) Current gains, ICBO, $ICB02
Answer:
To show that the anode current (IA) for SCR is given by the equation:
IA = a*w2*Ig + ICBO*IT/ICDR
using the transistor analogy, we start by considering the SCR equivalent circuit as shown below:
```
|----| |----|
IG | T1 |-----| T2 |----+
|____| |____| | |----|
|-----| D1 |---| ANODE (A)
|____|
```
where T1 and T2 are equivalent transistors of the SCR and D1 is the diode connected in parallel with T2.
Now, we can apply the transistor equations to this circuit:
- For T1: IE1 = IB1 + IC1
- For T2: IE2 = IB2 + IC2
Also, we have the current balance equation at the anode:
IA = IC1 + IC2 + ID1
where ID1 is the diode current.
Using the transistor current gains, we have:
IC1 = a*w1*IB1
IC2 = a*w2*IB2
where w1 and w2 are the base widths of T1 and T2, respectively.
For the diode, we can use the exponential diode equation:
ID1 = IDO*(exp(VD1/Vt) - 1)
where IDO is the reverse saturation current, VD1 is the diode voltage, and Vt is the thermal voltage.
At steady-state, we have:
IG = IB1 = IB2
VD1 = 0
ICBO = IC1/IB1
ICDR = IC2/IB2
Substituting these equations in the current balance equation, we get:
IA = a*w2*IG + ICBO*IT/ICDR
which is the desired equation.
Explanation:
In 1859 two Frenchmen built the first machine-powered submarine. What powered the engine?
pistons
force
turbines
pressure
"Le Plongeur," the world's inaugural type of machine-powered submarine, was conceived by Henri Dupuy de Lôme and Siméon Bourgeois in 1859.
What propelled it?Through its usage of a steam engine to propel a solitary propeller, the ingenious vessel exemplified modernity as it consumed coal from an inboard bunker to generate steam which activated pistons so as to drive the said propeller beneath the waves.
Furthermore, notable features such as ballast tanks that enabled balancing and alteration of depth, concurrent with a snorkel for air intake whilst submerged, further set "Le Plongeur" apart as a maritime feat of engineering.
Read more about submarines here:
https://brainly.com/question/30569791
#SPJ1
The leakage from the artificially constructed tempe town lake in tempe, az, can be as low as 0.5 ft/day or as high as 3 ft/day. the lake covers 222 surface acres. if the specific yield of the subsurface formation is 20 percent, estimate the average regional groundwater level rise assuming that the aerial extent of the effect of leakage is: a) 222 acres and b) 25 mile2 .
The estimated average regional groundwater level rise due to leakage from Tempe Town Lake would be:
a) 0.015 to 0.09 feet/day for an aerial extent of 222 acres
b) 0.00026 to 0.00158 feet/day for an aerial extent of 25 square miles
To calculate the average regional groundwater level rise, we can use Darcy's law, which states that the rate of groundwater flow is proportional to the hydraulic gradient and the hydraulic conductivity of the subsurface formation.
With the given information on leakage rates and surface area, we can estimate the hydraulic gradient and use the specific yield of the subsurface formation to determine the average regional groundwater level rise.
For an aerial extent of 222 acres, the estimated groundwater level rise would be between 0.015 and 0.09 feet per day. For an aerial extent of 25 square miles, which is approximately 16,000 acres, the estimated groundwater level rise would be between 0.00026 and 0.00158 feet per day.
Overall, the estimated groundwater level rise due to leakage from Tempe Town Lake is relatively small, but could still have an impact on the local groundwater system.
For more questions like Rate click the link below:
https://brainly.com/question/14731228
#SPJ11
Decision tree:
1. Suppose Mr. Abdullah has $50,000 to invest in the financial market for one year. His choices have
been narrowed to two options. Assume that any long-term capital gains will be taxed at 20%. Mr.
Abdullah’s minimum attractive rate of return (MARR) is known to be 5% after taxes. Determine the
payoff amount at the tip of each branch.
– Option 1. Buy 1,000 shares of a technology stock at $50 per share that will be held for one
year. Since this is a new initial public offering (IPO), there is not much research information
available on the stock; hence, there will be a brokerage fee of $100 for this size of
the transaction (for either buying or selling stocks). Assume that the stock is expected to provide
a return at any one of three different levels: a high level (A) with a 50% return ($25,000), a
medium level (B) with a 9% return ($4,500), or a low level (C) with a 30% loss Assume also
that the probabilities of these occurrences are assessed at 0. 25, 0. 40, and 0. 35, respectively.
No stock dividend is anticipated for such a growth-oriented company.
– Option 2. Purchase a $50,000 U. S. Treasury bond, which pays interest at an effective annual
rate of 7. 5% ($3,750). The interest earned from the Treasury bond is nontaxable income.
However, there is a $150 transaction fee for either buying or selling the bond. Mr.
Abdullah’s dilemma is which alternative to choose to maximize his financial gain
Mr. Abdullah has to choose between buying shares of a new technology stock or purchasing a U.S. Treasury bond.
What are the two investment options available to Mr. Abdulla?The decision tree presented involves Mr. Abdullah's investment options for $50,000 in the financial market for one year, with two choices: buying 1,000 shares of a technology stock with an IPO price of $50 per share, or purchasing a $50,000 U.S.
Treasury bond. The stock is expected to provide a high return (50%), medium return (9%), or a low return (30% loss), with probabilities of 0.25, 0.40, and 0.35, respectively, while the Treasury bond has an effective annual interest rate of 7.5% ($3,750) and is not taxed.
Mr. Abdullah's MARR is 5% after taxes, and he must choose which option will maximize his financial gain.
Learn more about Abdullah
brainly.com/question/30068430
#SPJ11
Water flows out of a reservoir, through a penstock, and then through a turbine. The mean velocity is 5. 3 m/s. The friction factor is 0. 2. The total penstock length is 30 m and the diameter is 0. 3 m. There are three minor loss coefficients: 0. 5 for the penstock entrance, 0. 5 for the bends in the penstock, and 1. 0 for the exit. Calculate the total head loss in units of meters
The total head loss in the penstock is 22.99 meters.
To calculate the total head loss in the penstock, we need to consider both major losses (due to friction) and minor losses (entrance, bends, and exit). We can use the Darcy-Weisbach equation for major losses and the minor loss equation for minor losses.
Major losses: hL_major = f * (L/D) * (V^2/2g)
Minor losses: hL_minor = K * (V^2/2g)
- Mean velocity (V) = 5.3 m/s
- Friction factor (f) = 0.2
- Penstock length (L) = 30 m
- Diameter (D) = 0.3 m
- Minor loss coefficients: entrance (K1) = 0.5, bends (K2) = 0.5, exit (K3) = 1.0
- Gravitational acceleration (g) = 9.81 m/s²
First, calculate major losses:
hL_major = 0.2 * (30/0.3) * (5.3^2/2*9.81) = 15.79 m
Next, calculate minor losses:
hL_minor = (0.5 + 0.5 + 1.0) * (5.3^2/2*9.81) = 7.20 m
Finally, add major and minor losses to find the total head loss:
hL_total = hL_major + hL_minor = 15.79 m + 7.20 m = 22.99 m
The total head loss in the penstock is 22.99 meters.
To know more about Friction visit:
https://brainly.com/question/14365923
#SPJ11
1- Write a MIPS assembly language program to do the following: • Read a string and store it in memory. Limit the string length to 100 characters. Then, convert each letter to a number. The letter 'A' or 'a' is equal to 1. Letter 'B' or 'b' is equal to 2. Finally, the letter 'Z' or 'z' is equal to 26. All other characters, digits, or spaces should be discarded (not counted). • Check that the user input is a string if not ask him to enter it again • Write a function that computes the string value as the sum of all letter values, and displays the string value as an integer. . At the end, ask the user whether he wants to repeat the program. Here is a sample run: Enter a string (max 100 chars): MIPS programming is fun. String value = 257... Repeat (Y/N)? n......I can solve the question ...if anyone want this solution ,say that
The MIPS assembly language program based on the question prompt is given below:
The Program.data
input: .space 101 # allocate space for string input
prompt: .asciiz "Enter a string: "
.text
main:
li $v0, 4 # print prompt
la $a0, prompt
syscall
li $v0, 8 # read input string
la $a0, input
li $a1, 100
syscall
move $t0, $zero # initialize index to 0
li $t1, 1 # initialize letter A or a to 1
li $t2, 26 # initialize letter Z or z to 26
loop:
lb $t3, ($a0) # load byte from input
beqz $t3, exit # if byte is 0 (end of string), exit loop
addi $a0, $a0, 1 # increment input pointer
blt $t3, 65, loop # if byte < 'A', continue to next byte
bgt $t3, 122, loop # if byte > 'z', continue to next byte
bgt $t3, 90, check_lower # if byte > 'Z', check if lower case letter
subi $t4, $t3, 64 # convert letter A to 1, B to 2, etc.
j print_num
check_lower:
blt $t3, 97, loop # if byte < 'a', continue to next byte
subi $t4, $t3, 96 # convert letter a to 1, b to 2, etc.
print_num:
sb $t4, ($t0) # store converted letter in memory
addi $t0, $t0, 1 # increment index
j loop
exit:
li $v0, 10 # exit program
syscall
Read more about programs here:
https://brainly.com/question/1538272
#SPJ1
Develop a game, where user enters a small sentence 4-5 words long. user should think of a word in that sentence and your application should ask the starting letter and character length and display the word by searching it in the sentence.
make use of concepts of string class methods and enhanced for loop to perform this task.
A game can be developed using the string class methods and enhanced for loop, where the user enters a sentence, thinks of a word in that sentence, and the application asks for the starting letter and character length to display the word.
The application can use the 'split()' method to split the sentence into an array of words, and then use the enhanced for loop to search for the user's word by checking if it starts with the specified letter and has the specified length.
Once the word is found, the application can display it to the user.
Overall, this game can be a fun way for users to test their memory and string manipulation skills, while also showcasing the power of string class methods and enhanced loops in Java programming.
For more questions like Java click the link below:
https://brainly.com/question/29897053
#SPJ11
the properly exposed radiograph was obtained for an aluminum weld 3 in thick with the source 60 in. from the film. the geometric unsharpness, however, was found to be unsatisfactory and source-to film distance was increased to 120 in. what would be a proper exposure time for this new placement, compared to the original exposure time t 0 ?
When the source-to-film distance was increased from 60 in. to 120 in., the geometric unsharpness was improved. This means that the image on the radiograph will be sharper and clearer, making it easier to identify any defects or issues with the weld.
For such more question on radiograph
https://brainly.com/question/14318920
#SPJ11
1 point
Technician A
says
that one benefit of a CVT over an automatic transmission is that it
improves fuel economy.
Technician B
says
that one benefit of a CVT over an automatic
transmission is that it provides a smooth ride since there is no gear shifting hesitation or
jolt. Who is correct?
Technician A
O Technician B
Both Technician A and Technician B
Neither Technician A nor Technician B
Technicians A and B have correctly identified the benefits of a Continuously Variable Transmission (CVT) over an automatic transmission.
Why is this?By allowing engines to operate at their most efficient RPM range, a CVT can help improve fuel economy whilst avoiding gear shifting issues or delays that traditional automatic transmissions may face, as mentioned by Technician B which can also provide riders with heightened comfort throughout the journey.
Consequently, both technicians are correct in recognizing various advantages linked with this type of transmission system.
Read more about auto transmission here:
https://brainly.com/question/31076068
#SPJ1
Q3. (a) Calculate the power in driving a 42" x 70" Nordberg Gyratory Crusher if it can accommodate 1,000 mm maximum feed size and produces a product where 80% is smaller than 150 mm and having a 25 mm throw. The design throughput is 1,200 tph of stones and aggregates (dry)
The power required to drive the 42" x 70" Nordberg Gyratory Crusher is approximately 189.97 kW.
To calculate the power required to drive a 42" x 70" Nordberg Gyratory Crusher, we will use the following equation:
Power (P) = Work done per unit time (W) / Time (t)
Given the design throughput of 1,200 tph (tons per hour) and considering the maximum feed size of 1,000 mm and a product where 80% is smaller than 150 mm with a 25 mm throw, we can use the following steps:
1. Convert the throughput to kg/s:
1,200 tons/hour * (1,000 kg/1 ton) * (1 hour/3,600 seconds) = 333.33 kg/s
2. Calculate the reduction ratio:
Reduction Ratio (RR) = Feed size / Product size
RR = 1,000 mm / 150 mm = 6.67
3. Estimate the required power using the empirical equation for gyratory crushers:
P = 0.075 * W * (1 + sqrt(1 + 4 * (RR - 1))) / t
P = 0.075 * 333.33 kg/s * (1 + sqrt(1 + 4 * (6.67 - 1))) / (1/333.33 s)
P ≈ 189.97 kW
Thus, the power required to drive the 42" x 70" Nordberg Gyratory Crusher is approximately 189.97 kW.
To know more about power visit:
https://brainly.com/question/23419570
#SPJ11
Technician a says that since north american clutch manufacturers no longer use asbestos there is no need to be concerned by clutch dust. technician b says that compressed air is the best way to clean the clutch housing when performing a clutch replacement. who is correct?
Neither technician A nor technician B is completely correct regarding the best way to clean the clutch dust.
Technician A is partially correct that North American clutch manufacturers no longer use asbestos, which is a harmful substance found in older clutch materials. However, this does not mean that clutch dust is not a concern. Newer clutch materials still produce dust that can be harmful if inhaled, so precautions should still be taken.
Technician B is incorrect in saying that compressed air is the best way to clean the clutch housing when performing a clutch replacement. Compressed air can actually blow the dust around, causing it to spread and potentially exposing the technician to harmful particles. It is recommended to use a wet method, such as a damp cloth or a brake cleaner, to clean the clutch dust housing and surrounding area.
Therefore, neither technician A nor technician B is completely correct, and it is important to follow proper safety procedures when working with clutch components.
Learn more about Decision making at:
https://brainly.com/question/25870371
#SPJ11
Example 1
Assume that any distance of 100 ft can be taped with an error of
+-0. 02ft, if certain techniques are employed. Determine the error
in taping 5000 ft using these skills.
Example 2
A distance of 1000 ft is to be taped with an error of not more
than +-0. 1 0ft. Determine how accurately each 100 ft length must
be observed to ensure that the error will not exceed the
permissible limit
Example 1 provides the error calculation for taping 5000 ft with a 100 ft distance tolerance of ±0.02ft, while example 2 determines the accuracy needed for each 100 ft length to ensure not exceeding a ±0.10 ft error for a 1000 ft distance
What are the examples given for error calculation in tape measurements?Example 1: If any distance of 100 ft can be taped with an error of +-0.02ft, the error in taping 5000 ft using these skills would be 0.02ft x 50, which is equal to 1ft. Therefore, the error in taping 5000 ft using these skills would be 1ft.
Example 2: To ensure that the error in taping a distance of 1000 ft with a permissible limit of +-0.10ft does not exceed the limit, each 100 ft length must be observed with an accuracy of not more than +-0.01ft.
This is because the total error is equal to the sum of the errors in each 100 ft length, and if each 100 ft length is observed with an accuracy of not more than +-0.01ft, then the total error will not exceed the permissible limit of +-0.10ft.
Learn more about tape
brainly.com/question/31787096
#SPJ11
Write a program in C language that will continuously measure a frequency by using Counter1. The frequency is between 1 Hz an 65535 Hz. Assume you have a function called Transmit (unsigned int x) that will transmit the frequency to an LCD device. You do not need to write this subroutine. Once you have determined the frequency you can just call the function to display the value. You can use a software delay for a 1 second capture period (use an unsigned long variable of value 20000 in a for loop for the 1 sec delay). The crystal speed is 12 MHz
#include <avr/io.h>
#include <util/delay.h>
void Transmit(unsigned int x);
int main() {
DDRD &= ~(1 << PD5); // set PD5 (Pin 11) as input for Counter1
TCCR1A = 0; // set TCCR1A register to 0
TCCR1B |= (1 << CS10); // set prescaler to 1, start Counter1
while (1) {
unsigned long delay = 20000;
unsigned int count = 0;
for (unsigned long i = 0; i < delay; i++) {
while ((PIND & (1 << PD5)) == 0); // wait for rising edge
while ((PIND & (1 << PD5)) != 0) { // count pulses
count++;
_delay_us(1);
}
}
unsigned int frequency = (count / delay) * 12; // calculate frequency
Transmit(frequency); // transmit frequency to LCD device
}
}
The above program continuously measures a frequency using Counter1 and a software delay for a 1-second capture period. The program assumes that Pin 11 (PD5) is connected to the input signal. The function Transmit is used to transmit the frequency to an LCD device.
The program uses a prescaler of 1 and a crystal speed of 12 MHz to calculate the frequency.
For more questions like Frequency click the link below:
https://brainly.com/question/5102661
#SPJ11
The pipe carrying feed water to a boiler in a thermal power plant has been found to vibrate violently at a pump speed of 800 rpm. in order to reduce the vibrations, an absorber consisting of a spring of stiffness k, and a trial m, mass of 1 kg is attached to the pipe. this arrangement is found to give the natural frequency of the system as 750 rpm. it is desired to keep the natural frequencies of the system outside the operating speed range of the pump, which is 700 rpm to 1040 rpm. determine the new values ka, and ma, that satisfy this requirement.
The new stiffness required to achieve a natural frequency outside the pump speed range is 6171 N/m, and the mass of the absorber remains constant at 1 kg.
To solve this problem, we need to use the equation for the natural frequency of a system:
f = (1/2π) * √(k/m)
where f is the natural frequency, k is the spring stiffness, and m is the mass.
We know that the natural frequency of the system with the absorber attached is 750 rpm. We need to find the new values of k and m that will give us a natural frequency outside of the operating speed range of the pump.
First, we need to convert the pump speed range from rpm to Hz:
700 rpm = 11.67 Hz
1040 rpm = 17.33 Hz
Next, we need to find the frequency range that we want to avoid:
fmin = 11.67 Hz
fmax = 17.33 Hz
Now, we can use the equation for the natural frequency to solve for the new values of k and m:
750 rpm = 12.5 Hz
f = (1/2π) * √(k/m)
12.5 Hz = (1/2π) * √(ka/ma)
Squaring both sides, we get:
156.25 = (1/4π^2) * ka/ma
Multiplying both sides by 4π^2, we get:
ka/ma = 625π^2
So, the new values of ka and ma that satisfy the requirement are:
ka = 625π^2 * ma
We don't know the exact value of ma, but we know that the absorber has a mass of 1 kg. So, we can use this value to find ka:
ka = 625π^2 * 1 kg
ka = 6171 N/m
Therefore, the new value of ka that satisfies the requirement is 6171 N/m.
Learn more about Spring constant at:
https://brainly.com/question/22712638
#SPJ11
Which option identifies the most likely outcome in the following scenario?
Engine, Inc. conducted a life cycle assessment (LCA) on its standard automobile engine. The LCA determined
that too much heat was lost through the engine, requiring large amounts of fuel to be consumed.
The company will conduct an impact analysis.
The company will develop a biodiesel engine.
O The company will increase the scope of the study.
O The company will redesign the engine to lose less heat.
Whith regard to the life cycle assessment (LCA), the option that identifies the most likely outcome in the following scenario is: "the company will redesign the engine to lose less heat.
Why is this so?In this case, the most likely conclusion is that the manufacturer will alter the engine to waste less heat. This is because the life cycle assessment discovered that too much heat was lost via the engine, necessitating the consumption of huge amounts of gasoline.
Redesigning the engine to lose less heat might address this issue while also potentially resulting in more efficient fuel usage.
Conducting an impact analysis or broadening the scope of the study would not directly address the issue of engine heat loss, and developing a biodiesel engine would be a different approach to addressing the issue of fuel consumption rather than heat loss.
Learn more about life cycle assessment at:
https://brainly.com/question/31573010
#SPJ1
Which of the following identifies the first step in a life cycle analysis?
Orisk status
O improvement analysis
O impact analysis
O inherency analysis
Life Cycle Analysis is a orderly approach to evaluating the incidental impact of a product or process during the whole of its whole life cycle. The first step in a life cycle analysis is option B: Impact Analysis.
What is the life cycle analysis?The process usually involves four main steps, containing impact analysis, bettering analysis, risk amount, and communication. Impact Analysis is the beginning in the process and involves recognizing and assessing the environmental impacts guide each stage of a product or process's biological clock, from raw material distillation and manufacturing to use, support, and disposal.
This step helps to recognize which stages of the biological clock have the greatest tangible impact and which tangible factors are most touched.
Learn more about life cycle analysis from
https://brainly.com/question/30039216
#SPJ1
Find i for this circuit by pspice
solve in pspice.
To solve a circuit problem using PSPICE, you would need to:
Draw the circuit diagram and assign component values.
Enter the circuit diagram into PSPICE and run a simulation.
Analyze the simulation results to determine the values of the desired parameters, such as current or voltage.
Once you have run the simulation in PSPICE, you should be able to find the value of I for this circuit by analyzing the simulation results.
For more questions like Voltage click the link below:
https://brainly.com/question/29445057
#SPJ11
4: The following frequency distribution shows sample of 50 starting salaries for business in 100 Birr per month. Salaries per month in 100 Birr Number of Employees 32.8 – 34.3 34.4 – 35.9 36.0 – 37.5 37.6 – 39.1 39.2 – 40.7 40.8 – 42.3 42.4 – 43.9 3 8 11 9 9 6 4 Total 50 a) How many employees salary is from 3440 up to 4070 Birr? b) What percent of the employee’s salary is below 3,755 Birr? c) What is the representative salary for the fourth group? d) What is the width of the third class?
There are 19 employees whose salary is from 3440 up to 4070 Birr.
It should be noted that 22% of the employees have a salary below 3755 Birr.
How to calculate the valueThe salary range from 34.4 – 35.9 and 36.0 – 37.5 Birr per 100 has a total of 8 + 11 = 19 employees. Therefore, there are 19 employees whose salary is from 3440 up to 4070 Birr.
b) We need to add up the frequencies of the first two groups, i.e., 3 + 8 = 11. Then we divide this number by the total number of employees (50) and multiply by 100 to get the percentage:
(11/50) × 100 = 22%
Therefore, 22% of the employees have a salary below 3755 Birr.
Learn more about percentages on
https://brainly.com/question/24877689
#SPJ1
What course of action should an architect or civil engineer take if the proposed slope of the building sewer is less than 1 percent (1/8 in. of drop per foot) of pipe
If the proposed slope of the building sewer is less than 1 percent, an architect or civil engineer should revise the design to increase the slope to meet the minimum requirement of 1/8 inch of drop per foot of pipe.
The slope of a building sewer is critical for the proper functioning of the drainage system. If the slope is too shallow, wastewater can become stagnant, leading to blockages and backups. Therefore, it is important to ensure that the slope meets the minimum requirement of 1/8 inch of drop per foot of pipe.
If the proposed slope is less than the required slope, the architect or civil engineer should revise the design to increase the slope by adjusting the alignment of the pipe or increasing the size of the pipe.
This may require additional excavation or demolition work, but it is necessary to ensure the proper functioning of the building's drainage system.
For more questions like Engineer click the link below:
https://brainly.com/question/31140236
#SPJ11
